ATTINY2313A-PU Atmel, ATTINY2313A-PU Datasheet - Page 113

• Manufacturer Part Number: ATTINY2313A-PU
• Description: IC MCU AVR 2K FLASH 20MHZ 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 18
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: ATtiny
• No. Of I/o's: 18
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.11.3
8246A–AVR–11/09
TCCR1C – Timer/Counter1 Control Register C
When the ICR1 is used as TOP value (see description of the WGM13:0 bits located in the
TCCR1A and the TCCR1B Register), the ICP1 is disconnected and consequently the Input Cap-
ture function is disabled.
• Bit 5 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be
written to zero when TCCR1B is written.
• Bit 4:3 – WGM13:2: Waveform Generation Mode
See TCCR1A Register description.
• Bit 2:0 – CS12:0: Clock Select
The three Clock Select bits select the clock source to be used by the Timer/Counter, see
12-10 on page 104
Table 12-6.
If external pin modes are used for the Timer/Counter1, transitions on the T1 pin will clock the
counter even if the pin is configured as an output. This feature allows software control of the
counting.
• Bit 7 – FOC1A: Force Output Compare for Channel A
• Bit 6 – FOC1B: Force Output Compare for Channel B
The FOC1A/FOC1B bits are only active when the WGM13:0 bits specifies a non-PWM mode.
However, for ensuring compatibility with future devices, these bits must be set to zero when
TCCR1A is written when operating in a PWM mode. When writing a logical one to the
FOC1A/FOC1B bit, an immediate compare match is forced on the Waveform Generation unit.
The OC1A/OC1B output is changed according to its COM1x1:0 bits setting. Note that the
FOC1A/FOC1B bits are implemented as strobes. Therefore it is the value present in the
COM1x1:0 bits that determine the effect of the forced compare.
Bit
0x22 (ox42)
Read/Write
Initial Value
CS12
0
0
0
0
1
1
1
1
CS11
0
0
1
1
0
0
1
1
FOC1A
Clock Select Bit Description
W
7
0
and
CS10
FOC1B
0
1
0
1
0
1
0
1
W
Figure 12-11 on page
6
0
Description
No clock source (Timer/Counter stopped).
clk
clk
clk
clk
clk
External clock source on T1 pin. Clock on falling edge.
External clock source on T1 pin. Clock on rising edge.
I/O
I/O
I/O
I/O
I/O
R
5
–
0
/1 (No prescaling)
/8 (From prescaler)
/64 (From prescaler)
/256 (From prescaler)
/1024 (From prescaler)
R
4
–
0
105.
R
3
–
0
R
2
–
0
R
1
–
0
R
0
–
0
TCCR1C
Figure
113