ATTINY2313A-PU Atmel, ATTINY2313A-PU Datasheet - Page 104

• Manufacturer Part Number: ATTINY2313A-PU
• Description: IC MCU AVR 2K FLASH 20MHZ 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 18
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: ATtiny
• No. Of I/o's: 18
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.9
104
Timer/Counter Timing Diagrams
ATtiny2313A/4313
an inverted PWM output can be generated by setting the COM1x1:0 to three (See
page
port pin is set as output (DDR_OCF1x). The PWM waveform is generated by setting (or clearing)
the OCF1x Register at the compare match between OCR1x and TCNT1 when the counter incre-
ments, and clearing (or setting) the OCF1x Register at compare match between OCR1x and
TCNT1 when the counter decrements. The PWM frequency for the output when using phase
and frequency correct PWM can be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x Register represents special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the
output will be continuously low and if set equal to TOP the output will be set to high for non-
inverted PWM mode. For inverted PWM the output will have the opposite logic values.
The Timer/Counter is a synchronous design and the timer clock (clk
clock enable signal in the following figures. The figures include information on when interrupt
flags are set, and when the OCR1x Register is updated with the OCR1x buffer value (only for
modes utilizing double buffering).
Figure 12-10. Timer/Counter Timing Diagram, Setting of OCF1x, no Prescaling
Figure 12-11
111). The actual OC1Fx value will only be visible on the port pin if the data direction for the
TCNTn
OCRnx
OCFnx
(clk
clk
clk
I/O
I/O
Tn
/1)
shows the same timing data, but with the prescaler enabled.
OCRnx - 1
f
OCnxPFCPWM
Figure 12-10
OCRnx
OCRnx Value
shows a timing diagram for the setting of OCF1x.
=
--------------------------- -
2 N TOP
⋅
f
clk_I/O
⋅
OCRnx + 1
T1
) is therefore shown as a
OCRnx + 2
Table 12-4 on
8246A–AVR–11/09