MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 3

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

High-Performance RISC CPU:
• Only 35 Instructions to Learn:
• Operating Speed:
• Interrupt Capability
• 8-Level Deep Hardware Stack
• Direct, Indirect and Relative Addressing modes
Special Microcontroller Features:
• Precision Internal Oscillator:
• Power-Saving Sleep mode
• Voltage Range:
• Industrial and Extended Temperature Range
• Power-on Reset (POR)
• Power-up Timer (PWRT) and Oscillator Start-up
• Brown-out Reset (BOR)
• Watchdog Timer (WDT) with Independent
• Multiplexed Master Clear with Pull-up/Input Pin
• Programmable Code Protection
• High Endurance Flash:
Low-Power Features:
• Standby Current:
• Operating Current:
• Watchdog Timer Current:
© 2009 Microchip Technology Inc.
- All single-cycle instructions except branches
- DC – 20 MHz oscillator/clock input
- DC – 200 ns instruction cycle
- Factory calibrated to ±1%, typical
- User selectable frequency: 4 MHz or 8 MHz
- PIC16F610/616: 2.0V to 5.5V
- PIC16HV610/616: 2.0V to user defined
Timer (OST)
Oscillator for Reliable Operation
- 100,000 write Flash endurance
- Flash retention: > 40 years
- 50 nA @ 2.0V, typical
- 20 μA @ 32 kHz, 2.0V, typical
- 220 μA @ 4 MHz, 2.0V, typical
- 1 μA @ 2.0V, typical
Note:
maximum (see note)
14-Pin Flash-Based, 8-Bit CMOS Microcontrollers
Voltage across internal shunt regulator
cannot exceed 5V.
PIC16F610/616/16HV610/616
Peripheral Features:
• Shunt Voltage Regulator (PIC16HV610/616 only):
• 11 I/O Pins and 1 Input Only
• Analog Comparator module with:
• Timer0: 8-Bit Timer/Counter with 8-Bit
• Enhanced Timer1:
• In-Circuit Serial Programming
PIC16F616/16HV616
• A/D Converter:
• Timer2: 8-Bit Timer/Counter with 8-Bit Period
• Enhanced Capture, Compare, PWM module:
- 5 volt regulation
- 4 mA to 50 mA shunt range
- High current source/sink for direct LED drive
- Interrupt-on-Change pins
- Individually programmable weak pull-ups
- Two analog comparators
- Programmable on-chip voltage reference
- Fixed Voltage Reference
- Comparator inputs and outputs externally
- SR Latch
- Built-In Hysteresis (user selectable)
Programmable Prescaler
- 16-bit timer/counter with prescaler
- External Timer1 Gate (count enable)
- Option to use OSC1 and OSC2 in LP mode
- Timer1 oscillator
Pins
- 10-bit resolution
- 8 external input channels
- 2 internal reference channels
Register, Prescaler and Postscaler
- 16-bit Capture, max. resolution 12.5 ns
- 16-bit Compare, max. resolution 200 ns
- 10-bit PWM with 1, 2 or 4 output channels,
(CV
accessible
as Timer1 oscillator if INTOSC mode
selected
programmable “dead time”, max. frequency
20 kHz
REF
) module (% of V
only:
DD
)
TM
(ICSP
DS41288F-page 3
TM
) via Two