MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 19

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.2.2.2
The OPTION register is a readable and writable regis-
ter, which contains various control bits to configure:
• Timer0/WDT prescaler
• External RA2/INT interrupt
• Timer0
• Weak pull-ups on PORTA
REGISTER 2-2:
© 2009 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
R/W-1
RAPU
OPTION Register
RAPU: PORTA Pull-up Enable bit
1 = PORTA pull-ups are disabled
0 = PORTA pull-ups are enabled by individual PORT latch values
INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of RA2/INT pin
0 = Interrupt on falling edge of RA2/INT pin
T0CS: Timer0 Clock Source Select bit
1 = Transition on RA2/T0CKI pin
0 = Internal instruction cycle clock (F
T0SE: Timer0 Source Edge Select bit
1 = Increment on high-to-low transition on RA2/T0CKI pin
0 = Increment on low-to-high transition on RA2/T0CKI pin
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
PS<2:0>: Prescaler Rate Select bits
INTEDG
R/W-1
OPTION_REG: OPTION REGISTER
BIT VALUE
000
001
010
011
100
101
110
111
W = Writable bit
‘1’ = Bit is set
R/W-1
T0CS
TIMER0 RATE WDT RATE
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
PIC16F610/616/16HV610/616
R/W-1
T0SE
1 : 1
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
OSC
/4)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
PSA
Note:
To achieve a 1:1 prescaler assignment for
Timer0, assign the prescaler to the WDT
by setting PSA bit to ‘1’ of the OPTION
register. See Section 5.1.3 “Software
Programmable Prescaler”.
R/W-1
PS2
x = Bit is unknown
R/W-1
PS1
DS41288F-page 19
R/W-1
PS0
bit 0