MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 161

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

TABLE 15-4:
© 2009 Microchip Technology Inc.
Standard Operating Conditions (unless otherwise stated)
Operating Temperature
30
31*
32
33*
34*
35*
36*
37*
Legend: TBD = To Be Determined
Note 1:
Param
No.
2:
3:
4:
*
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
T
T
T
T
T
V
V
T
OST
WDT
MC
PWRT
IOZ
BOR
BOR
HYST
Sym
These parameters are characterized but not tested.
only and are not tested.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator oper-
ation and/or higher than expected current consumption. All devices are tested to operate at “min” values
with an external clock applied to the OSC1 pin. When an external clock input is used, the “max” cycle time
limit is “DC” (no clock) for all devices.
By design.
Period of the slower clock.
To ensure these voltage tolerances, V
possible. 0.1 μF and 0.01 μF values in parallel are recommended.
L
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET PARAMETERS
MCLR Pulse Width (low)
Watchdog Timer Time-out
Period (No Prescaler)
Oscillation Start-up Timer
Period
Power-up Timer Period
I/O High-impedance from
MCLR Low or Watchdog Timer
Reset
Brown-out Reset Voltage
Brown-out Reset Hysteresis
Brown-out Reset Minimum
Detection Period
(1, 2)
-40°C ≤ T
Characteristic
A
CY
≤ +125°C
) equals four times the input oscillator time base period. All specified values
PIC16F610/616/16HV610/616
DD
and V
Min
100
2.0
10
10
40
—
—
—
2
5
SS
must be capacitivey decoupled as close to the device as
Typ†
1024
2.15
100
20
20
65
—
—
—
—
Max Units
140
2.0
2.3
—
—
30
35
—
—
—
T
mV
ms
ms
ms
OSC
μs
μs
μs
μs
V
V
V
V
V
(NOTE 3)
(NOTE 4)
V
DD
DD
DD
DD
DD
= 5V, -40°C to +85°C
= 5V, -40°C to +125°C
= 5V, -40°C to +85°C
= 5V, -40°C to +125°C
≤ V
BOR
Conditions
DS41288F-page 161