ATxmega128A1 Atmel Corporation, ATxmega128A1 Datasheet - Page 33

• Manufacturer Part Number: ATxmega128A1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128A1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 78
• Ext Interrupts: 78
• Usb Speed: No
• Usb Interface: No
• Spi: 12
• Twi (i2c): 4
• Uart: 8
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 8
• Output Compare Channels: 24
• Input Capture Channels: 24
• Pwm Channels: 24
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

4.16.6
8077H–AVR–12/09
LOCKBITS - Non-Volatile Memory Lock Bit Register
• Bit 5:4 - BODACT[1:0]: BOD operation in active mode
The BODACT fuse bits set the BOD operation mode when the device is in active and idle mode
of operation. For details on the BOD and BOD operation modes refer to
Out Detection” on page
Table 4-6.
• Bit 3 - EESAVE: EEPROM memory is preserved through the Chip Erase
A chip erase command will normally erase the Flash, EEPROM and internal SRAM. If the
EESAVE fuse is programmed, the EEPROM is not erased during chip erase. In case EEPROM
is used to store data independent of software revision, the EEPROM can be preserved through
chip erase.
Table 4-7.
Changing of the EESAVE fuse bit takes effect immediately after the write time-out elapses.
Hence, it is possible to update EESAVE and perform a chip erase according to the new setting
of EESAVE without leaving and re-entering programming mode
• Bit 2:0 - BODLEVEL[2:0] - Brown out detection voltage level
The BODLEVEL fuse bits sets the nominal BOD level value. During power-on the device is kept
in reset until the V
that the BOD level is set lower than the V
normal operation, refer to
nominal values, see
• Bit 7:6 - BLBB[1:0]: Boot Lock Bit Boot Loader Section
These bits indicate the locking mode for the Boot Loader Section. Even though the BLBB bits
are writable, they can only be written to a stricter locking. Resetting the BLBB bits is only possi-
ble by executing a Chip Erase Command.
Bit
+0x07
Read/Write
Initial Value
BODACT[1:0]
EESAVE
00
01
10
11
0
1
BOD operation modes in Active and Idle mode
EEPROM memory through Chip Erase
R/W
7
1
Description
Reserved
BOD enabled in sampled mode
BOD enabled continuously
BOD Disabled
Description
EEPROM is preserved during chip erase
EEPROM is not preserved during chip erase
CC
BLBB[1:0]
Table 9-2 on page
level has reached the programmed BOD level. Due to this always ensure
106.
R/W
6
1
Section 9.4 ”Reset Sources” on page 104
R/W
5
1
BLBA[1:0]
106.
CC
R/W
level, also if the BOD is not enabled and used during
4
1
R/W
3
1
BLBAT[1:0]
R/W
2
1
R/W
for details. For BOD level
1
1
LB[1:0]
Section 9.4.2 ”Brown-
XMEGA A
R/W
0
1
LOCKBITS
33