ATtiny40 Atmel Corporation, ATtiny40 Datasheet - Page 70

• Manufacturer Part Number: ATtiny40
• Manufacturer: Atmel Corporation

Specifications of ATtiny40

• Flash (kbytes): 4 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 18
• Ext Interrupts: 18
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

11.6.1
11.7
11.7.1
11.7.2
70
Modes of Operation
ATtiny40
Compare Output Mode and Waveform Generation
Normal Mode
Clear Timer on Compare Match (CTC) Mode
Register bit for the OC0x pin (DDR_OC0x) must be set as output before the OC0x value is visi-
ble on the pin. The port override function is independent of the Waveform Generation mode.
The design of the Output Compare pin logic allows initialization of the OC0x state before the out-
put is enabled. Note that some COM0x[1:0] bit settings are reserved for certain modes of
operation, see
The Waveform Generator uses the COM0x[1:0] bits differently in Normal, CTC, and PWM
modes. For all modes, setting the COM0x[1:0] = 0 tells the Waveform Generator that no action
on the OC0x Register is to be performed on the next Compare Match. For compare output
actions in the non-PWM modes refer to
Table 11-3 on page
A change of the COM0x[1:0] bits state will have effect at the first Compare Match after the bits
are written. For non-PWM modes, the action can be forced to have immediate effect by using
the 0x strobe bits.
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of the Waveform Generation mode (WGM0[2:0]) and Compare Out-
put mode (COM0x[1:0]) bits. The Compare Output mode bits do not affect the counting
sequence, while the Waveform Generation mode bits do. The COM0x[1:0] bits control whether
the PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-
PWM modes the COM0x[1:0] bits control whether the output should be set, cleared, or toggled
at a Compare Match (See
For detailed timing information refer to
11-10 on page 75
74.
The simplest mode of operation is the Normal mode (WGM0[2:0] = 0). In this mode the counting
direction is always up (incrementing), and no counter clear is performed. The counter simply
overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bot-
tom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV0) will be set in the same
timer clock cycle as the TCNT0 becomes zero. The TOV0 Flag in this case behaves like a ninth
bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt
that automatically clears the TOV0 Flag, the timer resolution can be increased by software.
There are no special cases to consider in the Normal mode, a new counter value can be written
anytime.
The Output Compare Unit can be used to generate interrupts at some given time. Using the Out-
put Compare to generate waveforms in Normal mode is not recommended, since this will
occupy too much of the CPU time.
In Clear Timer on Compare or CTC mode (WGM0[2:0] = 2), the OCR0A Register is used to
manipulate the counter resolution. In CTC mode the counter is cleared to zero when the counter
value (TCNT0) matches the OCR0A. The OCR0A defines the top value for the counter, hence
“Register Description” on page 76
and
77, and for phase correct PWM refer to
Figure 11-11 on page 76
“Modes of Operation” on page
Figure 11-8 on page
Table 11-2 on page
in
“Timer/Counter Timing Diagrams” on page
70).
Table 11-4 on page
75,
76. For fast PWM mode, refer to
Figure 11-9 on page
77.
8263A–AVR–08/10
75,
Figure