AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 164

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 10-2. Basic Mode WDT Timing Diagram, normal operation.
Figure 10-3. Basic Mode WDT Timing Diagram, no clear within T
10.5.1.6
10.5.2
32117C–AVR-08/11
C L R .W D T C L R
W a tc h d o g re s e t
t= t
C LR .W D T C LR
W a tch d og re set
W rite o n e to
t= t
W rite o n e to
0
0
Window Mode
Watchdog Reset
If the WDT counter is not cleared within T
see
A watchdog reset will result in a reset and the code will start executing from the boot vector,
please refer to the Power Manager chapter for details. If the Disable After Reset (DAR) bit in the
CTRL Register is zero, the WDT counter will restart counting from zero when the watchdog reset
is released.
If the CTRL.DAR bit is one the WDT will be disabled after a watchdog reset. Only the CTRL.EN
bit will be changed after the watchdog reset. However, if WDTAUTO fuse is configured to enable
the WDT after a watchdog reset, and the CTRL.FCD bit is zero, writing a one to the CTRL.DAR
bit will have no effect.
The window mode can protect against tight loops of runaway code. This is obtained by adding a
ban period to timeout period. During the ban period clearing the WDT counter is not allowed.
If the WDT Mode (MODE) bit in the CTRL Register is one, the WDT is in window mode. Note
that the CTRL.MODE bit can only be changed when the WDT is disabled (CTRL.EN=0).
Figure 10-3 on page
T
T
p s e l
p se l
164.
psel
psel
.
a watchdog reset will be issued at the end of T
T im eo u t
T im e o u t
AT32UC3C
164
psel
,