DV164136 Microchip Technology, DV164136 Datasheet - Page 45

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 3-1:
FIGURE 3-2:
3.2.3
In RC_RUN mode, the CPU and peripherals are
clocked from the internal oscillator block using the
INTOSC multiplexer. In this mode, the primary clock is
shut down. When using the INTRC source, this mode
provides the best power conservation of all the Run
modes, while still executing code. It works well for user
applications which are not highly timing-sensitive or do
not require high-speed clocks at all times.
If the primary clock source is the internal oscillator
block (either INTRC or INTOSC), there are no distin-
guishable
RC_RUN modes during execution. However, a clock
switch delay will occur during entry to and exit from
RC_RUN mode. Therefore, if the primary clock source
is the internal oscillator block, the use of RC_RUN
mode is not recommended.
© 2008 Microchip Technology Inc.
Peripheral
Note 1: Clock transition typically occurs within 2-4 T
Program
Counter
T1OSI
OSC1
Note1:T
Clock
Clock
RC_RUN MODE
CPU Clock
CPU
differences
PLL Clock
Peripheral
Program
Counter
Output
2: Clock transition typically occurs within 2-4 T
T1OSI
OSC1
Clock
OST
Q1
SCS1:SCS0 bits Changed
= 1024 T
Q2
PC
TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE
TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)
Q3
between
OSC
Q4
; T
Q1
PLL
Q1
= 2 ms (approx). These intervals are not shown to scale.
1
T
PRI_RUN
OST (1)
PC
2
Q2
Clock Transition
3
OSC
T
OSTS bit Set
Q3
PLL
and
.
OSC
(1)
.
(1)
PC + 2
n-1
Q4
This mode is entered by setting the SCS1 bit to ‘1’.
Although it is ignored, it is recommended that the SCS0
bit also be cleared; this is to maintain software compat-
ibility with future devices. When the clock source is
switched to the INTOSC multiplexer (see Figure 3-3),
the primary oscillator is shut down and the OSTS bit is
cleared. The IRCF bits may be modified at any time to
immediately change the clock speed.
n
PIC18F8722 FAMILY
Q1
1
Note:
Transition
2
Clock
n-1 n
(2)
Q2
Caution should be used when modifying a
single IRCF bit. If V
possible to select a higher clock speed
than is supported by the low V
Improper device operation may result if
the V
PC + 2
DD
Q3
/F
Q2
OSC
Q4
Q3 Q4
specifications are violated.
Q1
DD
Q1
PC + 4
Q2
is less than 3V, it is
PC + 4
Q2
DS39646C-page 43
Q3
Q3
DD
.