DV164136 Microchip Technology, DV164136 Datasheet - Page 234

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F8722 FAMILY
19.4.7
In I
reload value is placed in the lower 7 bits of the
SSPxADD register (Figure 19-17). When a write
occurs to SSPxBUF, the Baud Rate Generator will
automatically begin counting. The BRG counts down to
‘0’ and stops until another reload has taken place. The
BRG count is decremented twice per instruction cycle
(T
BRG is reloaded automatically.
Once the given operation is complete (i.e., transmis-
sion of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCLx pin
will remain in its last state.
Table 19-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPxADD.
FIGURE 19-17:
TABLE 19-3:
DS39646C-page 232
Note 1:
CY
2
C Master mode, the Baud Rate Generator (BRG)
) on the Q2 and Q4 clocks. In I
40 MHz
40 MHz
40 MHz
16 MHz
16 MHz
16 MHz
4 MHz
4 MHz
4 MHz
F
OSC
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE w/BRG
BAUD RATE GENERATOR BLOCK DIAGRAM
SSPM<3:0>
10 MHz
10 MHz
10 MHz
SCLx
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
F
2
CY
C Master mode, the
SSPM<3:0>
Control
Reload
CLKO
20 MHz
20 MHz
20 MHz
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
F
CY
*2
Reload
2
19.4.7.1
Because MSSP1 and MSSP2 are independent, they
can operate simultaneously in I
different baud rates. This is done by using different
BRG reload values for each module.
Because this mode derives its basic clock source from
the system clock, any changes to the clock will affect
both modules in the same proportion. It may be
possible to change one or both baud rates back to a
previous value by changing the BRG reload value.
BRG Down Counter
C specification (which applies to rates greater than
SSPxADD<6:0>
BRG Value
Baud Rate and Module
Interdependence
0Ch
18h
1Fh
63h
09h
27h
02h
09h
00h
© 2008 Microchip Technology Inc.
F
OSC
/4
(2 Rollovers of BRG)
2
C Master mode at
400 kHz
400 kHz
333 kHz
312.5 kHz
1 MHz
100 kHz
308 kHz
100 kHz
100 kHz
F
SCL
(1)
(1)
(1)
(1)