DV164136 Microchip Technology, DV164136 Datasheet - Page 281

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

21.6
Figure 21-4 shows the operation of the A/D converter
after the GO/DONE bit has been set and the
ACQT<2:0> bits are cleared. A conversion is started
after the following instruction to allow entry into Sleep
mode before the conversion begins.
Figure 21-5 shows the operation of the A/D converter
after the GO/DONE bit has been set, the ACQT<2:0>
bits are set to ‘010’ and a 4 T
selected before the conversion starts.
Clearing the GO/DONE bit during a conversion will abort
the current conversion. The A/D Result register pair will
NOT be updated with the partially completed A/D
conversion sample. This means the ADRESH:ADRESL
registers will continue to contain the value of the last
completed conversion (or the last value written to the
ADRESH:ADRESL registers).
FIGURE 21-4:
FIGURE 21-5:
© 2008 Microchip Technology Inc.
(Holding capacitor continues
acquiring input)
Set GO/DONE bit
1
T
CY
Set GO/DONE bit
T
A/D Conversions
Holding capacitor is disconnected from analog input (typically 100 ns)
ACQT
Acquisition
Automatic
- T
2
Time
AD
Conversion starts
Cycles
T
AD
3
1 T
A/D CONVERSION T
A/D CONVERSION T
AD
b9
4
2 T
Conversion starts
(Holding capacitor is disconnected)
AD
b8
AD
1
3 T
acquisition time is
AD
b9
2
b7
4 T
On the following cycle:
ADRESH:ADRESL are loaded, GO/DONE bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
AD
b8
3
b6
AD
AD
5 T
On the following cycle:
ADRESH:ADRESL are loaded, GO/DONE bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
CYCLES (ACQT<2:0> = 000, T
CYCLES (ACQT<2:0> =
AD
b5
b7
4
6 T
T
AD
b4
5
b6
AD
7 T
Cycles
After the A/D conversion is completed or aborted, a
2 T
be started. After this wait, acquisition on the selected
channel is automatically started.
21.7
The discharge phase is used to initialize the value of
the capacitor array. The array is discharged before
every sample. This feature helps to optimize the unity-
gain amplifier, as the circuit always needs to charge the
capacitor array, rather than charge/discharge based on
previous measure values.
PIC18F8722 FAMILY
AD
b3
b5
Note:
6
AD
8
wait is required before the next acquisition can
T
AD
b4
b2
Discharge
7
9 T
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
AD
b3
8
b1
010
10
T
, T
AD
b0
b2
ACQ
9
ACQ
11
= 0)
T
= 4 T
AD
10
Discharge
b1
1
AD
b0
DS39646C-page 279
11
)
T
Discharge
AD
1