ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 91
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 91 of 150
- Download datasheet (620Kb)
Philips Semiconductors
9397 750 12337
Product data
Table 62:
Bit
2
1
0
HcRhPortStatus[1:2] register: bit description
Symbol
PSS
PES
CCS
Rev. 03 — 06 January 2004
Description
On read—PortSuspendStatus: This bit indicates whether the port
is suspended or is in the resume sequence. It is set by a
SetSuspendState write and cleared when
PortSuspendStatusChange (PSSC) is set at the end of the resume
interval. This bit cannot be set if CurrentConnectStatus (CCS) is
cleared. This bit is also cleared when PortResetStatusChange
(PRSC) is set at the end of the port reset or when the HC is placed
in the USBResume state. If an upstream resume is in progress, it
should propagate to the HC.
0 — port is not suspended
1 — port is suspended
On write—SetPortSuspend: The HCD sets the
PortSuspendStatus (PSS) bit by writing logic 1 to this bit. Writing
logic 0 has no effect. If CurrentConnectStatus (CCS) is cleared,
this write does not set PortSuspendStatus (PSS); instead it sets
ConnectStatusChange (CSC). This informs the driver that it
attempted to suspend a disconnected port.
On read—PortEnableStatus: This bit indicates whether the port is
enabled or disabled. The Root Hub may clear this bit when an
overcurrent condition, disconnect event, switched-off power or
operational bus error, such as babble, is detected. This change
also causes PortEnabledStatusChange to be set. The HCD sets
this bit by writing SetPortEnable and clears it by writing
ClearPortEnable. This bit cannot be set when
CurrentConnectStatus (CCS) is cleared. This bit is also set, if it is
not already, at the completion of a port reset when
ResetStatusChange is set or port suspend when
SuspendStatusChange is set.
0 — port is disabled
1 — port is enabled
On write—SetPortEnable: The HCD sets PortEnableStatus (PES)
by writing logic 1. Writing logic 0 has no effect. If
CurrentConnectStatus (CCS) is cleared, this write does not set
PortEnableStatus (PES), but instead sets ConnectStatusChange
(CSC). This informs the driver that it attempted to enable a
disconnected port.
On read—CurrentConnectStatus: This bit reflects the current
state of the downstream port.
0 — no device connected
1 — device connected
On write—ClearPortEnable: The HCD writes logic 1 to this bit to
clear the PortEnableStatus (PES) bit. Writing logic 0 has no effect.
CurrentConnectStatus (CSC) is not affected by any write.
Remark: This bit always reads 1B when the attached device is
nonremovable (DeviceRemoveable[NDP]).
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
…continued
ISP1362
91 of 150
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors