ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 112

• Manufacturer Part Number: ISP1362EE/01
• Description: Single-chip Universal Serial Bus On-The-Go controller
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 107: DC command and register summary
[1]
[2]
[3]
[4]
[5]
[6]
9397 750 12337
Product data
Name
Read Endpoint n Status
(n = 1 to 14)
Validate Control OUT Buffer
Validate Control IN Buffer
Validate Endpoint n Buffer
(n = 1 to 14)
Clear Control OUT Buffer
Clear Control IN Buffer
Clear Endpoint n Buffer
(n = 1 to 14)
Unstall Control OUT Endpoint
Unstall Control IN Endpoint
Unstall Endpoint n
(n = 1 to 14)
Check Control OUT Status
Check Control IN Status
Check Endpoint n Status
(n = 1 to 14)
Acknowledge Set-up
General commands
Read Control OUT Error Code
Read Control IN Error Code
Read Endpoint n Error Code
(n = 1 to 14)
Unlock Device
Write or read DcScratch register
Read Frame Number
Read Chip ID
Read DcInterrupt register
With N representing the number of bytes, the number of words for 16-bit bus width is: (N + 1) divided by 2.
When accessing an 8-bit register in the 16-bit mode, the upper byte is invalid.
Validating an OUT endpoint buffer causes unpredictable behavior of the DC.
During the isochronous transfer in the 16-bit mode, because N
Clearing an IN endpoint buffer causes unpredictable behavior of the DC.
Reads a copy of the Status register: executing this command does not clear any status bits or interrupt bits.
[6]
[6]
[6]
Destination
DcEndpointStatus register n
endpoint 1 to 14
illegal: IN endpoints only
buffer memory endpoint 0 IN
buffer memory endpoint 1 to 14
(IN endpoints only)
buffer memory endpoint 0 OUT
illegal
buffer memory endpoint 1 to 14
(OUT endpoints only)
Endpoint 0 OUT
Endpoint 0 IN
Endpoint 1 to 14
DcEndpointStatusImage register
endpoint 0 OUT
DcEndpointStatusImage register
endpoint 0 IN
DcEndpointStatusImage register n
endpoint 1 to 14
Endpoint 0 IN and OUT
DcErrorCode register
endpoint 0 OUT
DcErrorCode register
endpoint 0 IN
DcErrorCode register
endpoint 1 to 14
all registers with write access
DcScratch register
DcFrameNumber register
DcChipID register
DcInterrupt register
[5]
Rev. 03 — 06 January 2004
…continued
[3]
[5]
1023, the firmware must manage the upper byte.
[3]
[3]
Code (Hex)
52 to 5F
(60)
61
62 to 6F
70
(71)
72 to 7F
80
81
82 to 8F
D0
D1
D2 to DF
F4
A0
A1
A2 to AF
B0
B2/B3
B4
B5
C0
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Transaction
read 1 byte
-
-
-
-
-
-
-
-
read 1 byte
read 1 byte
read 1 byte
-
read 1 byte
read 1 byte
read 1 byte
write 2 bytes
write or read 2 bytes
read 1 or 2 bytes
read 2 bytes
read 4 bytes
ISP1362
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[1]
112 of 150