ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 89
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 89 of 150
- Download datasheet (620Kb)
Philips Semiconductors
9397 750 12337
Product data
Table 62:
Bit
9
8
7 to 5
HcRhPortStatus[1:2] register: bit description
Symbol
LSDA
PPS
-
Rev. 03 — 06 January 2004
Description
On read—LowSpeedDeviceAttached: This bit indicates the
speed of the device attached to this port. When set, a low-speed
device is attached to this port. When cleared, a full-speed device is
attached to this port. This field is valid only when
CurrentConnectStatus (CCS) is set.
0 — full-speed device attached
1 — low-speed device attached
On write—ClearPortPower: The HCD clears the PortPowerStatus
(PPS) bit by writing logic 1 to this bit. Writing logic 0 has no effect.
On read—PortPowerStatus: This bit reflects the port power
status, regardless of the type of power switching implemented.
This bit is cleared if an overcurrent condition is detected. The HCD
sets this bit by writing SetPortPower or SetGlobalPower. The HCD
clears this bit by writing ClearPortPower or ClearGlobalPower.
PowerSwitchingMode (PCM) and PortPowerControlMask[NDP]
(PPCM[NDP]) determine which power control switches are
enabled. In the global switching mode (PowerSwitchingMode = 0),
only the Set/ClearGlobalPower command controls this bit. In the
per-port power switching (PowerSwitchingMode = 1), if the
PortPowerControlMask[NDP] (PPCM[NDP]) bit for the port is set,
only Set/ClearPortPower commands are enabled. If the mask is
not set, only Set/ClearGlobalPower commands are enabled. When
port power is disabled, CurrentConnectStatus (CCS),
PortEnableStatus (PES), PortSuspendStatus (PSS) and
PortResetStatus (PRS) should be reset.
0 — port power is OFF
1 — port power is ON
On write—SetPortPower: The HCD writes logic 1 to set the
PortPowerStatus (PPS) bit. Writing logic 0 has no effect.
Remark: This bit always reads logic 1 if power switching is not
supported.
reserved
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
…continued
ISP1362
89 of 150
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors