SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 209

• Manufacturer Part Number: SAM9263
• Manufacturer: Atmel Corporation

Specifications of SAM9263

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Can: 1
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

23.6.4
Register Name:SDRAMC_LPR
Addresses: 0xFFFFE210 (0), 0xFFFFE810 (1)
Access Type:Read-write
Reset Value: 0x0
• LPCB: Low-power Configuration Bits
• PASR: Partial Array Self-refresh (only for low-power SDRAM)
PASR parameter is transmitted to the SDRAM during initialization to specify whether only one quarter, one half or all banks
of the SDRAM array are enabled. Disabled banks are not refreshed in self-refresh mode. This parameter must be set
according to the SDRAM device specification.
• TCSR: Temperature Compensated Self-Refresh (only for low-power SDRAM)
TCSR parameter is transmitted to the SDRAM during initialization to set the refresh interval during self-refresh mode
depending on the temperature of the low-power SDRAM. This parameter must be set according to the SDRAM device
specification.
• DS: Drive Strength (only for low-power SDRAM)
DS parameter is transmitted to the SDRAM during initialization to select the SDRAM strength of data output. This parame-
ter must be set according to the SDRAM device specification.
6249I–ATARM–3-Oct-11
00
01
10
11
31
23
15
–
–
–
7
–
SDRAMC Low Power Register
Low Power Feature is inhibited: no Power-down, Self-refresh or Deep Power-down command is issued to
the SDRAM device.
The SDRAM Controller issues a Self-refresh command to the SDRAM device, the SDCLK clock is
deactivated and the SDCKE signal is set low. The SDRAM device leaves the Self Refresh Mode when
accessed and enters it after the access.
The SDRAM Controller issues a Power-down Command to the SDRAM device after each access, the
SDCKE signal is set to low. The SDRAM device leaves the Power-down Mode when accessed and
enters it after the access.
The SDRAM Controller issues a Deep Power-down command to the SDRAM device. This mode is
unique to low-power SDRAM.
30
22
14
–
–
–
6
PASR
29
21
13
–
–
5
TIMEOUT
28
20
12
–
–
4
27
19
11
–
–
3
–
DS
26
18
10
–
–
2
–
AT91SAM9263
25
17
–
–
9
1
TCSR
LPCB
24
16
–
–
8
0
251