ATmega32 Atmel Corporation, ATmega32 Datasheet - Page 80
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega32
Manufacturer Part Number
ATmega32
Description
Manufacturer
Atmel Corporation
Specifications of ATmega32
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATmega32-16AC
Manufacturer:
COMPAL
Quantity:
500
Part Number:
ATmega32-16AU
Manufacturer:
ATMEL
Quantity:
20 000
Part Number:
ATmega32-16PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega32-16PU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
8-bit
Timer/Counter
Register
Description
Timer/Counter Control
Register – TCCR0
2503Q–AVR–02/11
• Bit 7 – FOC0: Force Output Compare
The FOC0 bit is only active when the WGM00 bit specifies a non-PWM mode. However, for
ensuring compatibility with future devices, this bit must be set to zero when TCCR0 is written
when operating in PWM mode. When writing a logical one to the FOC0 bit, an immediate com-
pare match is forced on the Waveform Generation unit. The OC0 output is changed according to
its COM01:0 bits setting. Note that the FOC0 bit is implemented as a strobe. Therefore it is the
value present in the COM01:0 bits that determines the effect of the forced compare.
A FOC0 strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR0 as TOP.
The FOC0 bit is always read as zero.
• Bit 6, 3 – WGM01:0: Waveform Generation Mode
These bits control the counting sequence of the counter, the source for the maximum (TOP)
counter value, and what type of Waveform Generation to be used. Modes of operation sup-
ported by the Timer/Counter unit are: Normal mode, Clear Timer on Compare Match (CTC)
mode, and two types of Pulse Width Modulation (PWM) modes. See
Operation” on page
Table 38. Waveform Generation Mode Bit Description
Note:
• Bit 5:4 – COM01:0: Compare Match Output Mode
These bits control the Output Compare pin (OC0) behavior. If one or both of the COM01:0 bits
are set, the OC0 output overrides the normal port functionality of the I/O pin it is connected to.
However, note that the Data Direction Register (DDR) bit corresponding to the OC0 pin must be
set in order to enable the output driver.
Bit
Read/Write
Initial Value
Mode
0
1
2
3
1. The CTC0 and PWM0 bit definition names are now obsolete. Use the WGM01:0 definitions.
WGM01
(CTC0)
However, the functionality and location of these bits are compatible with previous versions of
the timer.
0
0
1
1
FOC0
W
7
0
73.
WGM00
(PWM0)
WGM00
R/W
0
1
0
1
6
0
COM01
Timer/Counter Mode
of Operation
Normal
PWM, Phase Correct
CTC
Fast PWM
R/W
5
0
COM00
R/W
4
0
WGM01
R/W
3
0
TOP
0xFF
0xFF
OCR0
0xFF
(1)
CS02
R/W
2
0
Update of
OCR0
TOP
Immediate
Immediate
BOTTOM
CS01
R/W
1
0
ATmega32(L)
Table 38
CS00
R/W
0
0
TOV0 Flag
Set-on
MAX
BOTTOM
MAX
MAX
TCCR0
and
“Modes of
80