SI1014-A-GM Silicon Laboratories Inc, SI1014-A-GM Datasheet - Page 34

• Manufacturer Part Number: SI1014-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1014-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 16kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1869-5

Si1010/1/2/3/4/5
34
CNVSTR
GPIO_0
GPIO_1
GPIO_2
IREF0
Name
XOUT
nIRQ
P0.4
P0.5
P0.6
P0.7
P1.4
P1.5
P1.6
XIN
RX
TX
Si1010/1
Si1012/3
Table 3.1. Pin Definitions for the Si1010/1/2/3/4/5 (Continued)
Pin Number
32
31
30
29
24
25
26
11
12
13
6
5
4
Si1014/5
32
31
30
29
24
25
26
12
13
11
6
5
4
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D I/O or
D Out
A Out
Type
A I/O
A I/O
A I/O
D In
D In
A In
A In
A In
A In
A In
A In
A In
D O
A O
A I
Port 0.4. See Port I/O section for a complete description.
UART TX Pin. See Port I/O section.
Port 0.5. See Port I/O section for a complete description.
UART RX Pin. See Port I/O section.
Port 0.6. See Port I/O section for a complete description.
External Convert Start Input for ADC0. See ADC0 section
for a complete description.
Port 0.7. See Port I/O section for a complete description.
IREF0 Output. See IREF section for complete description.
Port 1.4. See Port I/O section for a complete description.
Port 1.5. See Port I/O section for a complete description.
Port 1.6. See Port I/O section for a complete description.
General Purpose I/O controlled by the EZRadioPRO periph-
eral. May be configured through the EZRadioPRO registers
to perform various functions including: Clock Output, FIFO
status, POR, Wake-Up Timer, Low Battery Detect, TRSW,
AntDiversity control, etc. See the EZRadioPRO GPIO Con-
figuration Registers for more information.
EZRadioPRO peripheral interrupt status pin. Will be set low
to indicate a pending EZRadioPRO interrupt event. See the
EZRadioPRO Control Logic Registers for more details. This
pin is an open-drain output with a 220 k internal pullup
resistor. An external pull-up resistor is recommended.
EZRadioPRO peripheral crystal oscillator output. Connect
to an external 30 MHz crystal or leave floating if driving the
XIN pin with an external signal source.
EZRadioPRO peripheral crystal oscillator input. Connect to
an external 30 MHz crystal or to an external source. If using
an external clock source with no crystal, dc coupling with a
nominal 0.8 VDC level is recommended with a minimum
ac amplitude of 700 mVpp.
Rev. 1.0
Description