SI1014-A-GM Silicon Laboratories Inc, SI1014-A-GM Datasheet - Page 210

• Manufacturer Part Number: SI1014-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1014-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 16kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1869-5

Si1010/1/2/3/4/5
11. Clear the PMU0CF wake-up source flags. 
In Crystal Mode, the SmaRTClock oscillator may be driven by an external CMOS clock. The CMOS clock
should be applied to XTAL3. XTAL4 should be left floating. The input low voltage (VIL) and input high volt-
age (VIH) for XTAL3 when used with an external CMOS clock are 0.1 and 0.8 V, respectively. The SmaRT-
Clock oscillator should be configured to its lowest bias setting with AGC disabled. The CLKVLD bit is
indeterminate when using a CMOS clock, however, the OSCFAIL bit may be checked 2 ms after SmaRT-
Clock oscillator is powered on to ensure that there is a valid clock on XTAL3.
20.2.2. Using the SmaRTClock Oscillator in Self-Oscillate Mode
When using Self-Oscillate Mode, the XTAL3 and XTAL4 pins should be shorted together. The RTC0PIN
register can be used to internally short XTAL3 and XTAL4. The following steps show how to configure
SmaRTClock for use in Self-Oscillate Mode:
1. Set SmaRTClock to Self-Oscillate Mode (XMODE = 0).
2. Set the desired oscillation frequency: 
3. The oscillator starts oscillating instantaneously.
4. Fine tune the oscillation frequency by adjusting the load capacitance (RTC0XCF).
20.2.3. Using the Low Frequency Oscillator (LFO)
The low frequency oscillator provides an ultra low power, on-chip clock source to the SmaRTClock. The
typical frequency of oscillation is 16.4 kHz ±20%. No external components are required to use the LFO and
the XTAL3 and XTAL4 pins do not need to be shorted together. The LFO is only available on ‘F912 and
‘F902 devices.
The following steps show how to configure SmaRTClock for use with the LFO:
1. Enable and select the Low Frequency Oscillator (LFOEN = 1).
2. The LFO starts oscillating instantaneously.
When the LFO is enabled, the SmaRTClock oscillator increments bit 1 of the 32-bit timer (instead of bit 0).
This effectively multiplies the LFO frequency by 2, making the RTC timebase behave as if a 32.768 kHz
crystal is connected at the output.
20.2.4. Programmable Load Capacitance
The programmable load capacitance has 16 values to support crystal oscillators with a wide range of rec-
ommended load capacitance. If Automatic Load Capacitance Stepping is enabled, the crystal load capaci-
tors start at the smallest setting to allow a fast startup time, then slowly increase the capacitance until the
final programmed value is reached. The final programmed loading capacitor value is specified using the
LOADCAP bits in the RTC0XCF register. The LOADCAP setting specifies the amount of on-chip load
capacitance and does not include any stray PCB capacitance. Once the final programmed loading capaci-
tor value is reached, the LOADRDY flag will be set by hardware to logic 1.
When using the SmaRTClock oscillator in Self-Oscillate mode, the programmable load capacitance can be
used to fine tune the oscillation frequency. In most cases, increasing the load capacitor value will result in
a decrease in oscillation frequency.Table 20.2 shows the crystal load capacitance for various settings of
LOADCAP.
210
For oscillation at about 20 kHz, set BIASX2 = 0. 
For oscillation at about 40 kHz, set BIASX2 = 1.
Rev. 1.0