SI1014-A-GM Silicon Laboratories Inc, SI1014-A-GM Datasheet - Page 196

• Manufacturer Part Number: SI1014-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1014-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 16kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1869-5

Si1010/1/2/3/4/5
Important Note on External Crystals: Crystal oscillator circuits are quite sensitive to PCB layout. The
crystal should be placed as close as possible to the XTAL pins on the device. The traces should be as
short as possible and shielded with ground plane from any other traces which could introduce noise or
interference.
When using an external crystal, the external oscillator drive circuit must be configured by software for Crys-
tal Oscillator Mode or Crystal Oscillator Mode with divide by 2 stage. The divide by 2 stage ensures that the
clock derived from the external oscillator has a duty cycle of 50%. The External Oscillator Frequency Con-
trol value (XFCN) must also be specified based on the crystal frequency. The selection should be based on
Table 19.1. For example, a 25 MHz crystal requires an XFCN setting of 111b.
When the crystal oscillator is first enabled, the external oscillator valid detector allows software to deter-
mine when the external system clock has stabilized. Switching to the external oscillator before the crystal
oscillator has stabilized can result in unpredictable behavior. The recommended procedure for starting the
crystal is as follows:
1. Configure XTAL1 and XTAL2 for analog I/O and disable the digital output drivers.
2. Configure and enable the external oscillator.
3. Poll for XTLVLD => 1.
4. Switch the system clock to the external oscillator.
196
XFCN
000
001
010
100
101
011
110
111
Table 19.1. Recommended XFCN Settings for Crystal Mode
155 kHz  f 415 kHz
415 kHz  f 1.1 MHz
1.1 MHz  f 3.1 MHz
3.1 MHz  f 8.2 MHz
8.2 MHz  f 25 MHz
58 kHz  f 155 kHz
20 kHz f 58 kHz
Crystal Frequency
Figure 19.2. 25 MHz External Crystal Example
f  20 kHz
25 MHz
15 pF
15 pF
Rev. 1.0
Bias Current
10 Mohm
120 µA
550 µA
2.6 mA
0.5 µA
1.5 µA
4.8 µA
14 µA
40 µA
XTAL1
XTAL2
Typical Supply Current
3.0 µA, f = 32.768 kHz
4.8 µA, f = 32.768 kHz
9.6 µA, f = 32.768 kHz
193 µA, f = 400 kHz
3.9 mA, f = 25 MHz
28 µA, f = 400 kHz
71 µA, f = 400 kHz
940 µA, f = 8 MHz
(VDD = 2.4 V)