W971GG6JB-25 Winbond Electronics, W971GG6JB-25 Datasheet - Page 60

• Manufacturer Part Number: W971GG6JB-25
• Description: IC DDR2-800 SDRAM 1GB 84-WBGA
• Manufacturer: Winbond Electronics

Specifications of W971GG6JB-25

• Format - Memory: RAM
• Memory Type: DDR2 SDRAM
• Memory Size: 1G (64M x 16)
• Speed: 2.5ns
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.9 V
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 84-WBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q5804012

44. Data setup and hold time derating.
For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the data sheet tDS(base) and
tDH(base) value to the ΔtDS and ΔtDH derating value respectively. Example: tDS (total setup time) = tDS(base) + ΔtDS.
Setup (tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first
crossing of VIH(ac)min. Setup (tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of
VREF(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line between
shaded „VREF(dc) to AC region‟, use nominal slew rate for derating value. See Figure 24 Illustration of nominal slew rate for
tDS (differential DQS,
If the actual signal is later than the nominal slew rate line anywhere between shaded „VREF(dc) to AC region‟, the slew rate of a
tangent line to the actual signal from the AC level to DC level is used for derating value. See Figure 25 Illustration of tangent line
for tDS (differential DQS,
Hold (tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first
crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of
VIH(dc)min and the first crossing of VREF(dc). If the actual signal is always later than the nominal slew rate line between
shaded „DC level to VREF(dc) region‟, use nominal slew rate for derating value. See Figure 26 Illustration of nominal slew rate
for tDH (differential DQS,
If the actual signal is earlier than the nominal slew rate line anywhere between shaded „DC to VREF(dc) region‟, the slew rate of
a tangent line to the actual signal from the DC level to VREF(dc) level is used for derating value. See Figure 27 Illustration of
tangent line for tDH (differential DQS,
For slew rates in between the values listed in above DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential
data strobe table, the derating values may be obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac) at
the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
(V/nS)
Slew
Rate
DQ
2.0
1.5
1.0
0.9
0.8
0.7
0.6
0.5
0.4
DDR2-667, DDR2-800 and DDR2-1066 tDS/tDH derating with differential data strobe
ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH ΔtDS ΔtDH
100
67
ΔtDS, ΔtDH Derating Values for DDR2-667, DDR2-800 and DDR2-1066 (All units in „pS‟; the note applies to
4.0 V/nS
0
-
-
-
-
-
-
45
21
0
-
-
-
-
-
-
DQS
100
67
3.0 V/nS
-5
DQS
DQS
0
-
-
-
-
-
).
).
).
-14
45
21
0
-
-
-
-
-
100
-13
DQS
67
2.0 V/nS
-5
0
-
-
-
-
).
-14
-31
45
21
0
-
-
-
-
DQS/
-10
79
12
1.8 V/nS
-1
7
-
-
-
-
DQS Differential Slew Rate
-19
-42
33
12
-2
-
-
-
-
the entire table)
- 60 -
-10
24
19
11
1.6 V/nS
2
-
-
-
-
-30
-59
24
10
-7
-
-
-
-
-24
31
23
14
1.4 V/nS
2
-
-
-
-
Publication Release Date: Mar. 28, 2011
-18
-47
-89
22
5
-
-
-
-
-12
-52
35
26
14
1.2 V/nS
-
-
-
-
-140
-35
-77
17
-6
-
-
-
-
W971GG6JB
-40
38
26
1.0 V/nS
0
-
-
-
-
-
-128
-23
-65
6
-
-
-
-
-
Revision A07
-28
38
12
0.8 V/nS
-
-
-
-
-
-
-116
-11
-53
-
-
-
-
-
-