MT90520AG ZARLINK [Zarlink Semiconductor Inc], MT90520AG Datasheet - Page 73
MT90520AG
Manufacturer Part Number
MT90520AG
Description
8-Port Primary Rate Circuit Emulation AAL1 SAR
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.MT90520AG.pdf
(180 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 73 of 180
- Download datasheet (2Mb)
4.6.1.4
After being processed by the Correction/Detection state machine, all AAL1 header bytes (whether correctable or
not) and their corresponding validity indicators are passed to the Fast SN Processing state machine standardized
within ITU-T I.363.1. This second portion of the Sequence Number Checking sub-module is responsible for
analyzing the received sequence number values and determining whether the cells are being received in the
correct order. The Fast Sequence Number Processing state machine can detect and compensate for lost cells. In
addition, it can compensate for events which it determines to be misinserted cells.
UDT Mode of Operation
Although based on the state machine standardized in ITU-T I.363.1, additional functionality was added to the UDT
RX_SAR’s state machine in the form of two extra states:
•
•
The operation of the state machine is summarized in the following table:
x (don’t care)
reset_state
start
out_of_sync
The single_cell_loss_misinsertion state was added to provide for the insertion of in-order dummy cells in
the event of a single cell loss or misinsertion. As outlined in the table below, any time that an apparent
single-cell loss occurs, a dummy cell is inserted and then the received cell is accepted into the port’s
Reassembly Circular Buffer. If the event is indeed a single-cell loss, the subsequent received cell is
accepted and the state machine returns to the sync state. If the apparent single-cell loss turns out to have
been a cell misinsertion event, the state machine returns to sync, but the most recently received (i.e., late)
cell is discarded because a dummy cell was previously inserted in place of the misinserted cell. Similarly, if
the apparent single-cell loss turns out to have been a sequence number protection failure, the state machine
returns to sync and the most recently received cell is discarded because a dummy cell was previously
inserted (erroneously) when all of the cells were actually being received in order.
The late_cell_insertion state was added as a special user-programmable feature to provide CDV
monitoring. If the user enables the late-cell-checking feature (by setting the CHECK_LATE_ARRIVALS bit in
the UDT Reassembly Control Register at 2000h), when a per-port late-cell timeout counter reaches the
value programmed by the user, a late cell timeout is reached and the Fast SN Processing state machine
transitions into the late_cell_insertion state, inserting a single dummy cell on the transition. Once in the
late_cell_insertion state, the subsequent cell arrival will determine the type of event that occurred. If the
originally expected cell arrives, this is a late cell arrival case; the late cell is discarded and the state machine
returns to sync. If the cell which arrives has a sequence number greater by one than that which was
originally expected, a single cell loss has occurred; the received cell is accepted and the state machine
returns to sync.
Current State
Sequence Number Checking (Fast SN Processing State Machine)
Table 15 - Operation of UDT Fast Sequence Number Processing State Machine
reset asserted
reset de-asserted
invalid sequence number
valid sequence number
invalid sequence number
received cell is not in sequence with previous
cell
received cell is in sequence with previous cell
Transition Event
Zarlink Semiconductor Inc.
MT90520
73
- none
- none
- discard cell
- discard cell
- discard cell
- discard cell
- accept received cell
- per-port timeout circuitry is
enabled to permit late-cell
insertions
Action Taken
Next State
out_of_sync
out_of_sync
reset_state
start
start
start
sync
Data Sheet
Note
**
Related parts for MT90520AG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: