SAM3U2E Atmel Corporation, SAM3U2E Datasheet - Page 893

• Manufacturer Part Number: SAM3U2E
• Manufacturer: Atmel Corporation

Specifications of SAM3U2E

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 57
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 5
• Twi (i2c): 2
• Uart: 5
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 38-14. Comparison Waveform
6430E–ATARM–29-Aug-11
6430E–ATARM–29-Aug-11
Comparison Update
Comparison Match
CVMVUPD
CUPRUPD
CUPRCNT
CTRUPD
CPRUPD
CPRCNT
CVUPD
CCNT0
CMPM
CMPU
CUPR
CVM
CPR
CTR
CV
0x6
0x1
0x1
0x3
0x6
0x1
0x1
0x3
0x0
0x0
The update of the comparison x configuration and the comparison x value is triggered periodi-
cally after the comparison x update period. It is defined by the field CUPR in the PWM_CMPMx.
The comparison unit has an update period counter independent from the period counter to trig-
ger this update. When the value of the comparison update period counter CUPRCNT (in
PWM_CMPMx) reaches the value defined by CUPR, the update is triggered. The comparison x
update period CUPR itself can be updated while the channel 0 is enabled by using the
PWM_CMPMUPDx register.
CAUTION: to be taken into account, the write of the register PWM_CMPVUPDx must be fol-
lowed by a write of the register PWM_CMPMUPDx.
The comparison match and the comparison update can be source of an interrupt, but only if it is
enabled and not masked. These interrupts can be enabled by the
ter 2”
and the comparison update interrupt are reset by reading the
.
and disabled by the
0x1
0x1
0x2
0x2
0x0
0x2
0x3
0x2
0x3
0x1
“PWM Interrupt Disable Register 2”
0x2
0x2
0x0
0x3
0x2
0x0
0x1
0x1
0x2
0x2
0x0
0x3
0x6
0x1
0x0
“PWM Interrupt Status Register 2”
. The comparison match interrupt
0x2
0x1
“PWM Interrupt Enable Regis-
SAM3U Series
SAM3U Series
0x6
0x0
0x2
0x1
0x3
893
893