SAM3U2E Atmel Corporation, SAM3U2E Datasheet - Page 1036

• Manufacturer Part Number: SAM3U2E
• Manufacturer: Atmel Corporation

Specifications of SAM3U2E

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 96 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 57
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 5
• Twi (i2c): 2
• Uart: 5
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 36
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 40-8. DMAC Transfer with Linked List Source Address and Contiguous Destination Address
1036
SAM3U Series
Source Layer
Address of
SADDR(1)
SADDR(0)
SADDR(2)
Note:
The DMAC transfer might look like that shown in
nation address is decrementing.
The DMAC transfer flow is shown in
15. Once the buffer of data is transferred, the DMAC_CTRLAx register is written out to sys-
16. The DMAC does not wait for the buffer interrupt to be cleared, but continues and
tem memory at the same location and on the same layer (DMAC_DSCRx.DSCR_IF)
where it was originally fetched, that is, the location of the DMAC_CTRLAx register of
the linked list item fetched prior to the start of the buffer transfer. Only DMAC_CTRLAx
register is written out because only the DMAC_CTRLAx.BTSIZE and
DMAC_CTRLAX.DONE fields have been updated by DMAC hardware. Additionally, the
DMAC_CTRLAx.DONE bit is asserted when the buffer transfer has completed.
fetches the next LLI from the memory location pointed to by current DMAC_DSCRx
register and automatically reprograms the DMAC_SADDRx, DMAC_CTRLAx,
DMAC_CTRLBx and DMAC_DSCRx channel registers. The DMAC_DADDRx register
is left unchanged. The DMAC transfer continues until the DMAC samples the
DMAC_CTRLAx, DMAC_CTRLBx and DMAC_DSCRx registers at the end of a buffer
transfer match that described in Row 1 of
knows that the previous buffer transferred was the last buffer in the DMAC transfer.
Do not poll the DMAC_CTRLAx.DONE bit in the DMAC memory map. Instead, poll the
LLI.DMAC_CTRLAx.DONE bit in the LLI for that buffer. If the poll LLI.DMAC_CTRLAx.DONE bit is
asserted, then this buffer transfer has completed. This LLI.DMAC_CTRLAx.DONE bit was cleared
at the start of the transfer.
Source Buffers
Buffer 0
Buffer 1
Buffer 2
Figure 40-9 on page
Destination Buffers
Buffer 0
Buffer 2
Buffer 1
Table 40-1 on page
Figure 40-8 on page 1036
1037.
DADDR(2)
DADDR(1)
DADDR(0)
Destination Layer
1028. The DMAC then
Address of
6430E–ATARM–29-Aug-11
Note that the desti-