ATmega32U4 Atmel Corporation, ATmega32U4 Datasheet - Page 377

no-image

ATmega32U4

Manufacturer Part Number
ATmega32U4
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega32U4

Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
14
Hardware Qtouch Acquisition
No
Max I/o Pins
26
Ext Interrupts
13
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
3.3
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
12
Input Capture Channels
2
Pwm Channels
8
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega32U4-16AU
Manufacturer:
MAXIM
Quantity:
1 000
Part Number:
ATmega32U4-AU
Manufacturer:
FREESCALE
Quantity:
125
Part Number:
ATmega32U4-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega32U4-AU
Manufacturer:
MICROCHIP
Quantity:
200
Part Number:
ATmega32U4-AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega32U4-MUR
Manufacturer:
UCC
Quantity:
1 001
Part Number:
ATmega32U4RC-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega32U4RC-AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega32U4RC-MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
28.9.21
28.9.22
28.9.23
28.9.24
7766F–AVR–11/10
Programming the Lock Bits
Reading the Fuses and Lock Bits
Reading the Signature Bytes
Reading the Calibration Byte
6. Load data low byte using programming instructions 6e. A “0” will program the fuse, a “1”
7. Write Fuse low byte using programming instruction 6f.
8. Poll for Fuse write complete using programming instruction 6g, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Lock bit write using programming instruction 7a.
3. Load data using programming instructions 7b. A bit value of “0” will program the corre-
4. Write Lock bits using programming instruction 7c.
5. Poll for Lock bit write complete using programming instruction 7d, or wait for t
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Fuse/Lock bit read using programming instruction 8a.
3. To read all Fuses and Lock bits, use programming instruction 8e.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Signature byte read using programming instruction 9a.
3. Load address 0x00 using programming instruction 9b.
4. Read first signature byte using programming instruction 9c.
5. Repeat steps 3 and 4 with address 0x01 and address 0x02 to read the second and third
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Calibration byte read using programming instruction 10a.
3. Load address 0x00 using programming instruction 10b.
4. Read the calibration byte using programming instruction 10c.
will unprogram the fuse.
Table 28-13 on page
sponding lock bit, a “1” will leave the lock bit unchanged.
to
To only read Fuse High byte, use programming instruction 8b.
To only read Fuse Low byte, use programming instruction 8c.
To only read Lock bits, use programming instruction 8d.
signature bytes, respectively.
Table 28-13 on page
360).
360).
ATmega16/32U4
WLRH
WLRH
(refer to
(refer
377

Related parts for ATmega32U4