PIC16F636-I/P Microchip Technology Inc., PIC16F636-I/P Datasheet - Page 160

• Manufacturer Part Number: PIC16F636-I/P
• Description: 14 PIN, 3.5 KB FLASH, 128 RAM, 12 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F636-I/P

• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 12
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 14-pin PDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC12F635/PIC16F636/639
15.7
DS41232B-page 158
DC CHARACTERISTICS
D010E
D011E
D012E
D013E
D014E
D015E
D016E
D017E
D020
D021
D022A
D022B
D023
D024
D025
D026
D027
D028
Legend:
Note
Param
No.
1:
2:
3:
4:
†
DC Characteristics: PIC16F639-E (Extended)
I
I
I
I
I
DD
PD
ACT
STDBY
SLEEP
IWDT
IBOD
ILVD
ICMP
IV
IT1OSC
Sym
TBD = To Be Determined
Data in ‘Typ’ column is at 3.0V, 25 C unless otherwise stated. These parameters are for design guidance only and are not tested.
The test conditions for all I
stated, pulled to V
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate,
oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption.
The peripheral current is the sum of the base I
peripheral
calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep
mode, with all I/O pins in high-impedance state and tied to V
REF
Supply Current
Power-down Base Current
Active Current of AFE only
(receiving signal)
Standby Current of AFE only
(not receiving signal)
Sleep Current of AFE only
current can be determined by subtracting the base I
Device Characteristics
DD
2 LC Input Channels Enabled
3 LC Input Channels Enabled
1 LC Input Channel Enabled
; MCLR = V
3 LC Input Channel Signals
1 LC Input Channel Signal
(1,2)
DD
measurements in Active Operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-
DD
; WDT disabled.
(4)
DD
or I
Preliminary
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Supply Voltage
Min
PD
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
and the additional current consumed when this peripheral is enabled. The
DD
Typ†
TBD
TBD
0.99
TBD
TBD
110
190
220
370
140
180
320
340
500
180
320
1.2
0.3
1.8
3.3
6.1
4.0
4.6
0.2
18
70
58
58
85
10
—
.
9
3
4
5
DD
or I
PD
Max
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
16
—
5
6
7
1
current from this limit. Max values should be used when
Units
nA
nA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
2.0V
-40 C
V
V
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
2.0
3.0
3.6
3.6
3.6
3.6
3.6
3.6
DD
DD
T
A
© 2005 Microchip Technology Inc.
+125 C for extended
3.6V
WDT, BOD, Comparators, V
T1OSC disabled (excludes AFE)
WDT Current
BOD Current
PLVD Current
Comparator Current
CV
T1OSC Current
CS = V
(CW); Amplitude = 300 mV
channels enabled.
CS = V
CS = V
REF
Current
DD
DD
DD
Conditions
; Input = Continuous Wave
; ALERT = V
; ALERT = V
(3)
(3)
(3)
(3)
Note
(3)
DD
DD
PP
REF
. All
and