HD64F3337YCP16 Renesas Electronics America, HD64F3337YCP16 Datasheet - Page 411

• Manufacturer Part Number: HD64F3337YCP16
• Description: IC H8 MCU FLASH 60K 84PLCC
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300r

Specifications of HD64F3337YCP16

• Core Processor: H8/300
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: Host Interface, I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 74
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 84-PLCC
• Package: 84PLCC
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 74
• Interface Type: HIF/I2C/SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Bits 7 to 4—Reserved: These bits cannot be modified, and are always read as 1.
Bits 3 to 0—Large Block 3 to 0 (LB3 to LB0): These bits select large blocks (LB3 to LB0) to be
programmed and erased.
Bits 3 to 0:
LB3 to LB0
0
1
19.2.3
EBR2 is an 8-bit register that designates small flash-memory blocks for programming and erasure.
EBR2 is initialized to H'00 by a reset, in the standby modes, and when 12 V is not applied to the
FV
programmed and erased. Figure 19.2 and table 19.6 show a block map.
Note: * The initial value is H'00 in modes 2 and 3 (on-chip ROM enabled). In mode 1 (on-chip ROM
Bits 7 to 0—Small Block 7 to 0 (SB7 to SB0): These bits select small blocks (SB7 to SB0) to be
programmed and erased.
Bits 7 to 0:
SB7 to SB0
0
1
Bit
Initial value
Read/Write
PP
pin. When a bit in EBR2 is set to 1, the corresponding block is selected and can be
disabled), this register cannot be modified and always reads H'FF. For information on
accessing this register, refer to in section 19.7 Flash Memory Programming and erasing
Precautions (11).
Erase Block Register 2 (EBR2)
R/W*
SB7
Description
Block (LB3 to LB0) is not selected
Block (LB3 to LB0) is selected
Description
Block (SB7 to SB0) is not selected
Block (SB7 to SB0) is selected
7
0
R/W*
SB6
6
0
R/W*
SB5
5
0
R/W*
SB4
4
0
R/W*
SB3
3
0
R/W*
SB2
2
0
R/W*
SB1
1
0
(Initial value)
(Initial value)
R/W*
SB0
0
0
379