MCF5282CVF80J Freescale Semiconductor, MCF5282CVF80J Datasheet - Page 149

• Manufacturer Part Number: MCF5282CVF80J
• Description: IC MPU 512K FLASH 256MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVF80J

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 150
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Processor Series: MCF528x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: NNDK-MOD5282-KIT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

7.3.2.24 ColdFire Flash Module
The ColdFire Flash Control Module is capable of generating interrupts by the setting of the CBEIF or
CCIF bits in the CFMUSTAT. These interrupt sources, however, should not occur when the device is in a
low-power mode as long as no Flash operation was in progress when the low-power mode was entered.
When performing a program or erase operation on the Flash, if a command is active (CCIF = 0) when the
MCU enters a low-power mode, the command sequence monitor will perform the following:
7.3.2.25 BDM
Entering halt mode via the BDM port (by asserting the external BKPT pin) will cause the CPU to exit any
low-power mode.
7.3.2.26 JTAG
The JTAG (Joint Test Action Group) controller logic is clocked using the TCLK input and is not affected
by the system clock. The JTAG cannot generate an event to cause the CPU to exit any low-power mode.
Toggling TCLK during any low-power mode will increase the system current consumption.
7.3.3
The functionality of each of the peripherals and CPU during the various low-power modes is summarized
in
automatically assumes when the STOP instruction is executed and the LPCR[LPMD] field is set for the
particular low-power mode. Individual peripherals may be disabled by programming its dedicated control
bits. The wakeup capability field refers to the ability of an interrupt or reset by that peripheral to force the
CPU into run mode.
Freescale Semiconductor
Table
•
•
1. The command in progress will be aborted.
2. The Flash high voltage circuitry will be switched off and any pending command (CBEIF = 0) will
3. The CCIF and ACCERR flags will be set if a command is active when the MCU enters
No host access to the FlexCAN module.
The FlexCAN is neither in halt mode (MCR bit 8), in stop mode (MCT bit 15), nor in BUSOFF.
not be executed when the MCU exits low-power mode.
low-power mode.
7-7. The status of each peripheral during a given mode refers to the condition the peripheral
Summary of Peripheral State During Low-Power Modes
The state of any longword(s) being programmed, or any erase
pages/physical blocks being erased, is not guaranteed if the MCU enters
stop mode with a command in progress. Active commands are immediately
aborted when the MCU enters stop mode. Do not execute the STOP
instruction during program and erase operations.
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
NOTE
Power Management
7-13