AT90CAN128-15AZ Atmel, AT90CAN128-15AZ Datasheet - Page 314

• Manufacturer Part Number: AT90CAN128-15AZ
• Description: MCU AVR 128K FLASH 15MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90CANr

Specifications of AT90CAN128-15AZ

• Package / Case: 64-TQFP, 64-VQFP
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 53
• Eeprom Size: 4K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: CAN, I²C, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: AT90CANx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: CAN, SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATDVK90CAN1, ATADAPCAN01
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: 90C
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

23.7
314
AT90CAN32/64/128 Boundary-scan Order
AT90CAN32/64/128
The recommended values from
rithm in
“Actions” describes what JTAG instruction to be used before filling the Boundary-scan Register
with the succeeding columns. The verification should be done on the data scanned out when
scanning in the data on the same row in the table.
Table 23-8.
Using this algorithm, the timing constraint on the HOLD signal constrains the TCK clock fre-
quency. As the algorithm keeps HOLD high for five steps, the TCK clock frequency has to be at
least five times the number of scan bits divided by the maximum hold time, t
Table 23-9
selected as data path. Bit 0 is the LSB; the first bit scanned in, and the first bit scanned out. The
scan order follows the pin-out order as far as possible. Therefore, the bits of Port A is scanned in
the opposite bit order of the other ports. Exceptions from the rules are the Scan chains for the
analog circuits, which constitute the most significant bits of the scan chain regardless of which
physical pin they are connected to. In
Step
1
2
3
4
5
6
7
8
9
10
11
Table
Actions
SAMPLE_
PRELOAD
EXTEST
Verify the
COMP bit
scanned out
to be 0
Verify the
COMP bit
scanned out
to be 1
shows the Scan order between TDI and TDO when the Boundary-scan chain is
23-8. Only the DAC and port pin values of the Scan Chain are shown. The column
Algorithm for Using the ADC
ADCEN
1
1
1
1
1
1
1
1
1
1
1
DAC
0x200
0x200
0x200
0x123
0x123
0x200
0x200
0x200
0x143
0x143
0x200
Table 23-7
Figure
MUXEN
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
are used unless other values are given in the algo-
23-3, PXn. Data corresponds to FF0, PXn. Control
HOLD
1
0
1
1
1
1
0
1
1
1
1
PRECH
1
1
1
1
0
1
1
1
1
0
1
PA3.
Data
0
0
0
0
0
0
0
0
0
0
0
hold,max
PA3.
Control
0
0
0
0
0
0
0
0
0
0
0
7679H–CAN–08/08
PA3.
Pullup_
Enable
0
0
0
0
0
0
0
0
0
0
0