AT91SAM9R64-CU-999 Atmel, AT91SAM9R64-CU-999 Datasheet - Page 654

• Manufacturer Part Number: AT91SAM9R64-CU-999
• Description: IC MCU ARM9 64K SRAM 144LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9R64-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 72K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Data Converters: A/D 3x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: SPI, TWI, UART
• Maximum Clock Frequency: 240 MHz
• Number Of Programmable I/os: 118
• Operating Supply Voltage: 1.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9RL-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

39.5.2.3
654
AT91SAM9R64/RL64 Preliminary
FIFO
The datapath can be characterized by two parameters: initial_latency and cycles_per_data. The
parameter initial_latency is defined as the number of LCDC Core Clock cycles until the first data
is available at the output of the datapath. The parameter cycles_per_data is the minimum num-
ber of LCDC Core clock cycles between two consecutive data at the output interface.
These parameters are different for the different configurations of the LCD Controller and are
shown in
Table 39-2.
The FIFO block buffers the input data read by the DMA module. It contains two input FIFOs to
be used in Dual Scan configuration that are configured as a single FIFO when used in single
scan configuration.
The size of the FIFOs allows a wide range of architectures to be supported.
The upper threshold of the FIFOs can be configured in the FIFOTH field of the LCDFIFO regis-
ter. The LCDC core will request a DMA transfer when the number of words in each FIFO is less
than FIFOTH words. To avoid overwriting in the FIFO and to maximize the FIFO utilization, the
FIFOTH should be programmed with:
where:
TFT
STN Mono
STN Mono
STN Mono
STN Mono
STN Color
STN Color
STN Color
STN Color
• The output interface is a 24-bit data bus. The configuration of this interface depends on the
• The configuration interface connects the datapath with the configuration block. It is used to
• The control interface connects the datapath with the timing generation block. The main
• 512 is the effective size of the FIFO in words. It is the total FIFO memory size in single scan
• DMA_burst_length is the burst length of the transfers made by the DMA in words.
type of LCD used (TFT or STN, Single or Dual Scan, 4-bit, 8-bit, 16-bit or 24-bit interface).
select between the different datapath configurations.
control signal is the data-request signal, used by the timing generation module to request
new data from the datapath.
mode and half that size in dual scan mode.
DISTYPE
FIFOTH (in words) = 512 - (2 x DMA_BURST_LENGTH + 3)
Table
Datapath Parameters
39-2.
SCAN
Single
Single
Dual
Dual
Single
Single
Dual
Dual
Configuration
4
8
16
IFWIDTH
8
4
8
8
16
initial_latency
9
13
17
17
25
11
12
14
15
cycles_per_data
1
4
8
8
16
2
3
4
6
6289C–ATARM–28-May-09