PIC18F87K90-I/PTRSL Microchip Technology, PIC18F87K90-I/PTRSL Datasheet - Page 46

• Manufacturer Part Number: PIC18F87K90-I/PTRSL
• Description: MCU PIC 128K FLASH XLP 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F87K90-I/PTRSL

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 4096Byte
• Cpu Speed: 16MIPS
• No. Of Timers: 11
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 11
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F87K90 FAMILY
In the RC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 3-3 shows how the R/C combination is
connected.
FIGURE 3-3:
The RCIO Oscillator mode (Figure 3-4) functions like
the RC mode, except that the OSC2 pin becomes an
additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6).
FIGURE 3-4:
3.5.1
The EC and ECPLL Oscillator modes require an
external clock source to be connected to the OSC1 pin.
There is no oscillator start-up time required after a
Power-on Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 3-5 shows the pin connections for the EC
Oscillator mode.
DS39957B-page 46
C
V
C
Recommended values: 3 k  R
V
R
Recommended values: 3 k  R
R
EXT
SS
EXT
SS
EXT
EXT
V
V
DD
DD
RA6
EXTERNAL CLOCK INPUT
(EC MODES)
F
OSC
/4
RC OSCILLATOR MODE
OSC1
RCIO OSCILLATOR MODE
OSC1
OSC2/CLKO
I/O (OSC2)
20 pF C
20 pF C
EXT
EXT
EXT
EXT
 100 k
 100 k
 300 pF
 300 pF
PIC18FXXXX
PIC18FXXXX
Internal
Internal
Clock
Clock
Preliminary
oscillating source to produce frequencies up to 64 MHz.
FIGURE 3-5:
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 3-6. In
this configuration, the divide-by-4 output on OSC2 is
not available. Current consumption in this configuration
will be somewhat higher than EC mode, as the internal
oscillator’s feedback circuitry will be enabled (in EC
mode, the feedback circuit is disabled).
FIGURE 3-6:
3.5.2
A Phase Lock Loop (PLL) circuit is provided as an
option for users who want to use a lower frequency
oscillator circuit, or to clock the device up to its highest
rated frequency from a crystal oscillator. This may be
useful for customers who are concerned with EMI due
to high-frequency crystals, or users who require higher
clock speeds from an internal oscillator.
3.5.2.1
The HSPLL and ECPLL modes provide the ability to
selectively run the device at four times the external
The PLL is enabled by setting the PLLEN bit
(OSCTUNE<6>) or the PLLCFG bit (CONFIG1H<4>).
For the HF-INTOSC as primary, the PLL must be
enabled with the PLLEN. This provides software con-
trol for the PLL, enabling even if PLLCFG is set to ‘1’,
so that the PLL is enabled only when the HF-INTOSC
frequency is within the 4 MHz to 16 MHz input range.
This also enables additional flexibility for controlling the
application’s clock speed in software. The PLLEN
should be enabled in HF-INTOSC mode only if the
input frequency is in the range of 4 MHz-16 MHz.
Clock from
Ext. System
Clock from
Ext. System
PLL FREQUENCY MULTIPLIER
F
HSPLL and ECPLL Modes
OSC
Open
/4
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
EXTERNAL CLOCK INPUT
OPERATION (HS OSC
CONFIGURATION)
 2010 Microchip Technology Inc.
OSC1/CLKI
OSC2/CLKO
OSC1
OSC2
PIC18F87K90
PIC18F87K90
(HS Mode)