PIC18F87K90-I/PTRSL Microchip Technology, PIC18F87K90-I/PTRSL Datasheet - Page 297

• Manufacturer Part Number: PIC18F87K90-I/PTRSL
• Description: MCU PIC 128K FLASH XLP 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F87K90-I/PTRSL

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 4096Byte
• Cpu Speed: 16MIPS
• No. Of Timers: 11
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 11
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

20.10 Operation During Sleep
The LCD module can operate during Sleep. Setting the
SLPEN bit (LCDCON<6>) allows the LCD module to go
to Sleep. Clearing this bit allows the module to continue
operating during Sleep.
If a SLEEP instruction is executed and SLPEN = 1, the
LCD module will cease all functions and go into a very
low-current consumption mode. The module will stop
operation immediately and drive the minimum LCD volt-
age on both segment and common lines. Figure 20-19
shows this operation.
The LCD module current consumption will not
decrease in this mode, but the overall consumption of
the device will be lower due to shut down of the core
and other peripheral functions.
To ensure that no DC component is introduced on the
panel, the SLEEP instruction should be executed
immediately after an LCD frame boundary. The LCD
FIGURE 20-19:
 2010 Microchip Technology Inc.
COM0
COM1
COM2
SEG0
SLEEP ENTRY/EXIT WHEN SLPEN = 1 OR CS<1:0> = 00
2 Frames
SLEEP Instruction Execution
Preliminary
PIC18F87K90 FAMILY
interrupt can be used to determine the frame boundary.
For the formulas to calculate the delay, see
Section 20.9 “LCD Interrupts”.
If a SLEEP instruction is executed and SLPEN = 0, the
module will continue to display the current contents of
the LCDDATA registers. The LCD data cannot be
changed.
To allow the module to continue operation while in
Sleep, the clock source must be either the internal RC
oscillator or Timer1 external oscillator.
If the system clock is selected and the module is
programmed to not Sleep, the module will ignore the
SLPEN bit and stop operation immediately. The
minimum LCD voltage then will be driven onto the
segments and commons.
Note:
Wake-up
The internal RC oscillator or external
SOSC oscillator must be used to operate
the LCD module during Sleep.
DS39957B-page 297
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
3
2
1
0
3
2
1
0
3
2
1
0
3
2
1
0