PIC18F87K90-I/PTRSL Microchip Technology, PIC18F87K90-I/PTRSL Datasheet - Page 411

• Manufacturer Part Number: PIC18F87K90-I/PTRSL
• Description: MCU PIC 128K FLASH XLP 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F87K90-I/PTRSL

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 4096Byte
• Cpu Speed: 16MIPS
• No. Of Timers: 11
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 11
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

The CTMU current source may be trimmed with the
trim bits in CTMUICON using an iterative process to get
the exact current desired. Alternatively, the nominal
value without adjustment may be used. That value may
be stored by software, for use in all subsequent
capacitive or time measurements.
To calculate the value for R
must be chosen. Then, the resistance can be
calculated.
For example, if the A/D Converter reference voltage is
3.3V, use 70% of full scale (or 2.31V) as the desired
approximate voltage to be read by the A/D Converter. If
the range of the CTMU current source is selected to be
0.55  A, the resistor value needed is calculated as,
R
if the current source is chosen to be 5.5  A, R
be 420,000 Ω, and 42,000 Ω if the current source is set
to 55  A.
FIGURE 27-2:
 2010 Microchip Technology Inc.
CAL
= 2.31V/0.55 A , for a value of 4.2 M Ω . Similarly,
ANx
R
CAL
CTMU CURRENT SOURCE
CALIBRATION CIRCUIT
Current Source
MUX
PIC18F87K90
CAL
A/D Converter
, the nominal current
A/D
A/D
Trigger
CTMU
CAL
would
Preliminary
PIC18F87K90 FAMILY
A value of 70% of full-scale voltage is chosen to make
sure that the A/D Converter was in a range that is well
above the noise floor. If an exact current is chosen to
incorporate the trimming bits from CTMUICON, the
resistor value of R
ingly. R
resistor values. R
available, in light of the precision needed for the circuit
that the CTMU will be measuring. A recommended
minimum would be 0.1% tolerance.
The following examples show a typical method for
performing a CTMU current calibration.
• Example 27-1 demonstrates how to initialize the
• Example 27-2 demonstrates one method for the
A/D Converter and the CTMU.
This routine is typical for applications using both
modules.
actual calibration routine.
This method manually triggers the A/D Converter to
demonstrate the entire step-wise process. It is also
possible to automatically trigger the conversion by
setting the CTMU’s CTTRIG bit (CTMUCONH<0>).
CAL
also may be adjusted to allow for available
CAL
CAL
should be of the highest precision
may need to be adjusted accord-
DS39957B-page 411