LPC2478FBD208,551 NXP Semiconductors, LPC2478FBD208,551 Datasheet - Page 711

• Manufacturer Part Number: LPC2478FBD208,551
• Description: IC ARM7 MCU 512K LCD 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2478FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/IrDA/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, DK-35TS-LPC2478, DK-57TS-LPC2478, DK-57VTS-LPC2478, SOMDIMM-LPC2478, SAB-TFBGA208, KSK-LPC2478-JL, MCB2470
• Development Tools By Supplier: OM11015, OM11019, OM11022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1034 - PROGRAMMERS, DEVELOPMENT SYSTEMS622-1033 - KIT LCD TOUCH 5.7" FOR LPC2478MCB2470 - BOARD EVAL NXP LPC247X SERIESOM11022 - EVAL LPC-STICK WITH LPC2478OM11019 - BOARD EVAL FOR LPC2478568-4742 - MODULE DIMM LPC2478 ARM7568-4741 - KIT LCD TOUCH 5.7" FOR LPC2478622-1028 - KIT LCD TOUCH 5.7" FOR LPC2478KSDKLPC2478-PL - KIT IAR KICKSTART NXP LPC2478622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4369 - BOARD EVAL FOR LPC2478622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4363; 935284069551; LPC2478FBD208-S

1. Basic configuration
2. Introduction
3. Features of the GPDMA
UM10237_4
User manual
The GPDMA is configured using the following registers:
The General Purpose DMA Controller (GPDMA) is an AMBA AHB compliant peripheral
allowing selected LPC2400 peripherals to have DMA support.
1. Power: In the PCONP register
2. Clock: see
3. Interrupts are enabled in the VIC using the VICIntEnable register
4. Initialization: see
•
•
•
•
•
•
•
•
•
•
•
•
UM10237
Chapter 32: LPC24XX General Purpose DMA (GPDMA)
controller
Rev. 04 — 26 August 2009
Remark: On reset, the GPDMA is disabled (PCGPDMA = 0).
Two DMA channels. Each channel can support a unidirectional transfer.
The GPDMA provides 16 peripheral DMA request lines. Some of these are connected
to peripheral functions that support DMA: the SD/MMC, two SSP, and I2S interfaces.
Single DMA and burst DMA request signals. Each peripheral connected to the
GPDMA can assert either a burst DMA request or a single DMA request. The DMA
burst size is set by programming the GPDMA.
Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and
peripheral-to-peripheral transfers.
Scatter or gather DMA is supported through the use of linked lists. This means that
the source and destination areas do not have to occupy contiguous areas of memory.
Hardware DMA channel priority. Each DMA channel has a specific hardware priority.
DMA channel 0 has the highest priority and channel 1 has the lowest priority. If
requests from two channels become active at the same time the channel with the
highest priority is serviced first.
AHB slave DMA programming interface. The GPDMA is programmed by writing to the
DMA control registers over the AHB slave interface.
One AHB bus master for transferring data. This interface transfers data when a DMA
request goes active.
32-bit AHB master bus width.
Incrementing or non-incrementing addressing for source and destination.
Programmable DMA burst size. The DMA burst size can be programmed to more
efficiently transfer data. Usually the burst size is set to half the size of the FIFO in the
peripheral.
Internal four-word FIFO per channel.
Table
4–53.
Section
Rev. 04 — 26 August 2009
32–5.
(Table
4–63), set bit PCGPDMA.
(Section
© NXP B.V. 2009. All rights reserved.
User manual
7–3.4).
711 of 792