AT32AP7001-ALUT Atmel, AT32AP7001-ALUT Datasheet - Page 597

• Manufacturer Part Number: AT32AP7001-ALUT
• Description: IC MCU 32BIT AVR32 208-LQFP
• Manufacturer: Atmel
• Series: AVR®32 AP7r

Specifications of AT32AP7001-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: EBI/EMI, I²C, MMC, PS2, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²C, POR, PWM, WDT
• Number Of I /o: 90
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: D/A 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: EBI, ISI, MCI, PS2, SPI, TWI, USB
• Maximum Clock Frequency: 150 MHz
• Number Of Programmable I/os: 90
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 16 bit, 1 Channel
• Package: 208PQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 150 MHz
• Operating Supply Voltage: 1.8 V
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATNGW100 - KIT AVR32 NETWORK GATEWAYATSTK1000 - KIT STARTER FOR AVR32AP7000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

1 = The direction bit from card to host in the response has not been detected.
•
0 = No error.
1 = A mismatch is detected between the command index sent and the response index received. Cleared when writing in
the CMDR.
• SDIOIRQB: SDIO Interrupt for Slot B
0 = No interrupt detected on SDIO Slot B.
1 = A SDIO Interrupt on Slot B has reached. Cleared when reading the SR.
• SDIOIRQA: SDIO Interrupt for Slot A
0 = No interrupt detected on SDIO Slot A.
1 = A SDIO Interrupt on Slot A has reached. Cleared when reading the SR.
•
This flag must be used only for Write Operations.
A block write operation uses a simple busy signalling of the write operation duration on the data (DAT0) line: during a data
transfer block, if the card does not have a free data receive buffer, the card indicates this condition by pulling down the data
line (DAT0) to LOW. The card stops pulling down the data line as soon as at least one receive buffer for the defined data
transfer block length becomes free.
The NOTBUSY flag allows to deal with these different states.
0 = The MCI is not ready for new data transfer. Cleared at the end of the card response.
1 = The MCI is ready for new data transfer. Set when the busy state on the data line has ended. This corresponds to a free
internal data receive buffer of the card.
Refer to the MMC or SD Specification for more details concerning the busy behavior.
•
0 = No data transfer in progress.
1 = The current data transfer is still in progress, including CRC16 calculation. Cleared at the end of the CRC16 calculation.
• BLKE: Data Block Ended
This flag must be used only for Write Operations.
0 = A data block transfer is not yet finished. Cleared when reading the SR.
1 = A data block transfer has ended, including the CRC16 Status transmission.
The flag is set for each transmitted CRC Status.
Refer to the MMC or SD Specification for more details concerning the CRC Status.
•
0= The last data written in TDR has not yet been transferred in the Shift Register.
1= The last data written in TDR has been transferred in the Shift Register.
•
0 = No data has been received since the last read of RDR.
1 = Data has been received since the last read of RDR.
32015G–AVR32–09/09
RINDE: Response Index Error
NOTBUSY: Data Not Busy
DTIP: Data Transfer in Progress
TXRDY: Transmit Ready
RXRDY: Receiver Ready
AT32AP7001
597