DS21458-W+ Maxim Integrated, DS21458-W+ Datasheet - Page 94
DS21458-W+
Manufacturer Part Number
DS21458-W+
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS21458-W.pdf
(269 pages)
Specifications of DS21458-W+
Product
Framer
Number Of Transceivers
4
Data Rate
64 Kbps
Supply Current (max)
328 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
CSBGA
Minimum Operating Temperature
0 C
Operating Supply Voltage
3.3 V
Supply Voltage - Max
3.465 V
Supply Voltage - Min
3.135 V
Part # Aliases
90-21458+W00
- Current page: 94 of 269
- Download datasheet (2Mb)
DS21455/DS21458 Quad T1/E1/J1 Transceivers
17.1.1 Processor-Based Receive Signaling
The robbed-bit signaling (T1) or TS16 CAS signaling (E1) is sampled in the receive data stream and
copied into the receive signaling registers, RS1 through RS16. In T1 mode, only RS1 through RS12 are
used. The signaling information in these registers is always updated on multiframe boundaries. This
function is always enabled.
17.1.1.1 Change Of State
In order to avoid constant monitoring of the receive signaling registers, the DS21455/DS21458 can be
programmed to alert the host when any specific channel or channels undergo a change of their signaling
state. RSCSE1 through RSCSE4 for E1 and RSCSE1 through RSCSE3 for T1 are used to select which
channels can cause a change of state indication. The change of state is indicated in Status Register 5
(SR1.5). If signaling integration, CCR1.5, is enabled then the new signaling state must be constant for
three multiframes before a change of state indication is indicated. The user can enable the INT pin to
toggle low upon detection of a change in signaling by setting the IMR1.5 bit. The signaling integration
mode is global and cannot be enabled on a channel-by-channel basis.
The user can identity which channels have undergone a signaling change of state by reading the
RSINFO1 through RSINFO4 registers. The information from this registers will tell the user which RSx
register to read for the new signaling data. All changes are indicated in the RSINFO1–RSINFO4 register
regardless of the RSCSE1–RSCSE4 registers.
17.1.2 Hardware-Based Receive Signaling
In hardware-based signaling the signaling data can be obtained from the RSER pin or the RSIG pin.
RSIG is a signaling PCM-stream output on a channel-by-channel basis from the signaling buffer. The
signaling data, T1 robbed bit or E1 TS16, is still present in the original data stream at RSER. The
signaling buffer provides signaling data to the RSIG pin and also allows signaling data to be reinserted
into the original data stream in a different alignment that is determined by a multiframe signal from the
RSYNC pin. In this mode, the receive elastic store can be enabled or disabled. If the receive elastic store
is enabled, then the backplane clock (RSYSCLK) can be either 1.544MHz or 2.048MHz. In the ESF
framing mode, the ABCD signaling bits are output on RSIG in the lower nibble of each channel. The
RSIG data is updated once a multiframe (3ms) unless a freeze is in effect. In the D4 framing mode, the
AB signaling bits are output twice on RSIG in the lower nibble of each channel. Hence, bits 5 and 6
contain the same data as bits 7 and 8 respectively in each channel. The RSIG data is updated once a
multiframe (1.5ms) unless a freeze is in effect. See the Functional Timing Diagrams for some examples.
17.1.2.1 Receive-Signaling Reinsertion at RSER
In this mode, the user will provide a multiframe sync at the RSYNC pin and the signaling data will be
reinserted based on this alignment. In T1 mode, this results in two copies of the signaling data in the
RSER data stream. The original signaling data based on the Fs/ESF frame positions and the realigned
data based on the user supplied multiframe sync applied at RSYNC. In voice channels this extra copy of
signaling data is of little consequence. Reinsertion can be avoided in data channels since this feature is
activated on a per-channel basis. For reinsertion, the elastic store must be enabled; however, the
backplane clock can be either 1.544MHz or 2.048MHz.
Signaling reinsertion mode is enabled, on a per-channel basis by setting the RSRCS bit high in the PCPR
register. The channels that are to have signaling reinserted are selected by writing to the PCDR1-PCDR3
registers for T1 mode and PCDR1–PCDR4 registers for E1 mode. In E1 mode, the user will generally
select all channels when doing reinsertion.
94 of 269
Related parts for DS21458-W+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC LIU QUAD T1/E1/J1 256-CSBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Network Controller & Processor ICs Quad E1-T1-J1 Single -Chip Transceiver (S
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products