DS21458LDK Maxim Integrated, DS21458LDK Datasheet - Page 159
DS21458LDK
Manufacturer Part Number
DS21458LDK
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS21458LDK.pdf
(269 pages)
- Current page: 159 of 269
- Download datasheet (2Mb)
Figure 25-2. Basic Unbalanced Network Connections
25.1 LIU Operation
The analog AMI/HDB3 waveform off of the E1 line or the AMI/B8ZS waveform off of the T1 line is
transformer coupled into the RTIP and RRING pins of the DS21455/DS21458. The user has the option to
use internal termination, software selectable for 75Ω/100Ω/120Ω applications, or external termination.
The LIU recovers clock and data from the analog signal and passes it through the jitter attenuation MUX
outputting the received line clock at RCLKO and bipolar or NRZ data at RPOSO and RNEGO. The
DS21455/DS21458 contain an active filter that reconstructs the analog received signal for the nonlinear
losses that occur in transmission. The receive circuitry also is configurable for various monitor
applications. The device has a usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB for T1,
which allows the device to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in
length. Data input at TPOSI and TNEGI is sent via the jitter attenuation MUX to the wave shaping
circuitry and line driver. The DS21455/DS21458 will drive the E1 or T1 line from the TTIP and TRING
pins via a coupling transformer. The line driver can handle both CEPT 30/ISDN-PRI lines for E1 and
long-haul (CSU) or short-haul (DSX-1) lines for T1.
25.2 LIU Receiver
The DS21455/DS21458 contain a digital clock recovery system. The device couples to the receive E1 or
T1 twisted pair (or coaxial cable in 75Ω E1 applications) via a 1:1 transformer. See
transformer details. The DS21455/DS21458 have the option of using software-selectable termination
requiring only a single, fixed pair of termination resistors.
The DS21455/DS21458’s LIU is designed to be fully software selectable for E1 and T1 without the need
to change any external resistors for the receive-side. The receive-side will allow the user to configure the
device for 75Ω, 100Ω, or 120Ω receive termination by setting the RT1 (LIC4.1) and RT0 (LIC4.0) bits.
When using the internal termination feature, the resistors labeled R in
external termination is required, the resistors labeled R in
each, depending on the line impedance.
Tx
Rx
60 *
0.047 F
159 of 269
0.01 F
60 *
TTIP
TRING
RTIP
RRING
*USE 60 WHEN USING INTERNAL TERMINATION FEATURE.
Figure 25-5
DS21455/DS21458 Quad T1/E1/J1 Transceivers
DS21455
DS21458
will need to be 37.5Ω, 50Ω, or 60Ω
Table 25-5
/
should be 60Ω each. If
Table 25-8
for
Related parts for DS21458LDK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC LIU QUAD T1/E1/J1 256-CSBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Network Controller & Processor ICs Quad E1-T1-J1 Single -Chip Transceiver (S
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Network Controller & Processor ICs
Manufacturer:
Maxim Integrated
Datasheet:
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products