S25FL512SAGMFIG13 Spansion, S25FL512SAGMFIG13 Datasheet - Page 34
![no-image](/images/no-image-200.jpg)
S25FL512SAGMFIG13
Manufacturer Part Number
S25FL512SAGMFIG13
Description
Flash 512Mb 3V 133MHz Serial NOR Flash
Manufacturer
Spansion
Datasheet
1.S25FL512SAGMFI011.pdf
(143 pages)
Specifications of S25FL512SAGMFIG13
Rohs
yes
Memory Type
Flash
Memory Size
512 MB
Architecture
Uniform
Timing Type
Asynchronous
Interface Type
SPI
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
Operating Temperature
- 40 C to + 85 C
Mounting Style
SMD/SMT
Package / Case
SO-16
- Current page: 34 of 143
- Download datasheet (5Mb)
5.3
34
5.2.3
Power-Up and Power-Down
Input Signal Overshoot
During DC conditions, input or I/O signals should remain equal to or between V
transitions, inputs or I/Os may overshoot V
The device must not be selected at power-up or power-down (that is, CS# must follow the voltage applied on
V
V
V
A simple pull-up resistor (generally of the order of 100 k) on Chip Select (CS#) can usually be used to insure
safe and proper power-up and power-down.
The device ignores all instructions until a time delay of t
the minimum V
V
After power-up (t
current (I
During power-down or voltage drops below V
of t
above V
the event Power-on Reset (POR) did not complete correctly after power up, the assertion of the RESET#
signal or receiving a software reset command (RESET) will restart the POR process.
Normal precautions must be taken for supply rail decoupling to stabilize the V
device in a system should have the V
connection (this capacitor is generally of the order of 0.1 µf).
CC
CC
PD
) until V
CC
SS
returns below V
for the part to initialize correctly on power-up. See
at power-down
(min) at power-up, and then for a further delay of t
CC
SB
(cut-off) the part will stay initialized and will work correctly when V
), and the WEL bit is reset.
V
CC
IO
reaches the correct value as follows:
CC
+ 2.0V
PU
- 2.0V
threshold. See
V
V
), the device is in Standby mode (not Deep Power Down mode), draws CMOS standby
CC
IL
IH
(min) during t
Figure 5.1 Maximum Negative Overshoot Waveform
Figure 5.2 Maximum Positive Overshoot Waveform
D a t a
Figure
PU
CC
20 ns
20 ns
. No command should be sent to the device until the end of t
S25FL512S
5.3. However, correct operation of the device is not guaranteed if
rail decoupled by a suitable capacitor close to the package supply
S h e e t
SS
CC
to –2.0V or overshoot to V
(cut-off), the voltage must drop below V
( P r e l i m i n a r y )
PU
20 ns
20 ns
Figure
PU
has elapsed after the moment that V
5.4. If during a voltage drop the V
20 ns
20 ns
IO
+2.0V, for periods up to 20 ns.
S25FL512S_00_04 June 13, 2012
CC
CC
SS
is again above V
supply at the device. Each
and V
CC
IO
. During voltage
(low) for a period
CC
rises above
CC
CC
PU
(min). In
stays
.
Related parts for S25FL512SAGMFIG13
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![S34ML01G100TFI000](/images/no-image3.png)
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
![S34ML04G100TFI000](/images/no-image3.png)
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
![AM29F010B-70EC](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29DL322GT70WMI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29DL323GB90WMI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29F400TC-70PFTN](/images/no-image3.png)
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
![AM29F010B70JI](/images/no-image3.png)
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
![S29AL016D70BAI020](/images/no-image3.png)
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![S29AL016M90FAI010](/images/no-image3.png)
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![S29AL016M90FAI020](/images/no-image3.png)
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![AM49LV128BMH15NT](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM49PDL127BH](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29DL800TA-90PFTN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29DL800BA-90PFTN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29F010B-90JI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: