C8051F962-A-GM Silicon Labs, C8051F962-A-GM Datasheet - Page 404

• Manufacturer Part Number: C8051F962-A-GM
• Description: 8-bit Microcontrollers - MCU 128KB, DC-DC, AES DQFN76
• Manufacturer: Silicon Labs

Specifications of C8051F962-A-GM

• Rohs: yes
• Core: 8051
• Processor Series: C8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 128 KB
• Data Ram Size: 8448 B
• On-chip Adc: Yes
• Operating Supply Voltage: 2.5 V to 3.3 V
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: DQFN-76
• Mounting Style: SMD/SMT
• Number Of Programmable I/os: 57
• Number Of Timers: 4

C8051F96x
29.2. Operational Modes
UART0 provides standard asynchronous, full duplex communication. The UART mode (8-bit or 9-bit) is
selected by the S0MODE bit (SCON0.7). Typical UART connection options are shown below.
29.2.1. 8-Bit UART
8-Bit UART mode uses a total of 10 bits per data byte: one start bit, eight data bits (LSB first), and one stop
bit. Data are transmitted LSB first from the TX0 pin and received at the RX0 pin. On receive, the eight data
bits are stored in SBUF0 and the stop bit goes into RB80 (SCON0.2).
Data transmission begins when software writes a data byte to the SBUF0 register. The TI0 Transmit Inter-
rupt Flag (SCON0.1) is set at the end of the transmission (the beginning of the stop-bit time). Data recep-
tion can begin any time after the REN0 Receive Enable bit (SCON0.4) is set to logic 1. After the stop bit is
received, the data byte will be loaded into the SBUF0 receive register if the following conditions are met:
RI0 must be logic 0, and if MCE0 is logic 1, the stop bit must be logic 1. In the event of a receive data over-
run, the first received 8 bits are latched into the SBUF0 receive register and the following overrun data bits
are lost.
If these conditions are met, the eight bits of data is stored in SBUF0, the stop bit is stored in RB80 and the
RI0 flag is set. If these conditions are not met, SBUF0 and RB80 will not be loaded and the RI0 flag will not
be set. An interrupt will occur if enabled when either TI0 or RI0 is set.
29.2.2. 9-Bit UART
9-bit UART mode uses a total of eleven bits per data byte: a start bit, 8 data bits (LSB first), a programma-
ble ninth data bit, and a stop bit. The state of the ninth transmit data bit is determined by the value in TB80
(SCON0.3), which is assigned by user software. It can be assigned the value of the parity flag (bit P in reg-
ister PSW) for error detection, or used in multiprocessor communications. On receive, the ninth data bit
goes into RB80 (SCON0.2) and the stop bit is ignored.
404
SPACE
MARK
BIT TIMES
BIT SAMPLING
START
BIT
D0
Figure 29.3. UART Interconnect Diagram
Figure 29.4. 8-Bit UART Timing Diagram
D1
RS-232
MCU
D2
TX
RX
Rev. 0.5
D3
RS-232
LEVEL
XLTR
OR
D4
RX
RX
TX
TX
C8051Fxxx
D5
C8051Fxxx
D6
D7
STOP
BIT