PIC18F25J50 MICROCHIP [Microchip Technology], PIC18F25J50 Datasheet - Page 48
![no-image](/images/no-image-200.jpg)
PIC18F25J50
Manufacturer Part Number
PIC18F25J50
Description
28/44-Pin, Low-Power, High-Performance USB Microcontrollers with nanoWatt XLP Technology
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.PIC18F25J50.pdf
(562 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F25J50-I/SO
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50-I/SP
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50-I/SS
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50T-I/SO
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50T-I/SS
Manufacturer:
MICROCHIP
Quantity:
1 001
- Current page: 48 of 562
- Download datasheet (5Mb)
PIC18F46J50 FAMILY
TABLE 4-1:
4.1.3
The length of the transition between clock sources is
the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Two bits indicate the current clock source and its
status:
(T1CON<6>). In general, only one of these bits will be
set in a given power-managed mode. When the OSTS
bit is set, the primary clock would be providing the
device clock. When the T1RUN bit is set, the Timer1
oscillator would be providing the clock. If neither of
these bits is set, INTRC would be clocking the device.
4.1.4
The power-managed mode that is invoked with the
SLEEP instruction is determined by the setting of the
IDLEN and DSEN bits at the time the instruction is exe-
cuted. If another SLEEP instruction is executed, the
device will enter the power-managed mode specified
by IDLEN and DSEN at that time. If IDLEN or DSEN
have changed, the device will enter the new
power-managed mode specified by the new setting.
4.2
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
DS39931D-page 48
Sleep
Deep Sleep
PRI_RUN
SEC_RUN
RC_RUN
PRI_IDLE
SEC_IDLE
RC_IDLE
Note 1:
Note:
Mode
2:
Run Modes
OSTS
IDLEN and DSEN reflect their values when the SLEEP instruction is executed.
Deep Sleep turns off the voltage regulator for ultra low-power consumption. See
Mode”
CLOCK TRANSITIONS AND STATUS
INDICATORS
Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep or Deep
Sleep mode, or one of the Idle modes,
depending on the setting of the IDLEN bit.
MULTIPLE SLEEP COMMANDS
DSCONH<7>
DSEN
LOW-POWER MODES
0
1
0
0
0
0
0
0
for more information.
(OSCCON<3>)
(1)
IDLEN
N/A
N/A
N/A
OSCCON<7,1:0>
0
0
1
1
1
(1)
SCS<1:0>
and
N/A
N/A
00
01
11
00
01
11
T1RUN
Clocked
Clocked
Clocked
Off
CPU
Module Clocking
Off
Off
Off
Off
(2)
Peripherals
Clocked
Clocked
Clocked
Clocked
Clocked
Clocked
Off
Off
4.2.1
The PRI_RUN mode is the normal, full-power execu-
tion mode of the microcontroller. This is also the default
mode upon a device Reset unless Two-Speed Start-up
is enabled (see
for details). In this mode, the OSTS bit is set (see
Section 3.5.1 “Oscillator Control
4.2.2
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of low-power consumption while still using a
high-accuracy clock source.
SEC_RUN mode is entered by setting the SCS<1:0>
bits to ‘01’. The device clock source is switched to the
Timer1 oscillator (see
oscillator is shut down, the T1RUN bit (T1CON<6>) is
set and the OSTS bit is cleared.
Note:
Timer1 oscillator and/or RTCC may optionally be
enabled
RTCC can run uninterrupted using the Timer1 or
internal low-power RC oscillator
The normal, full-power execution mode; primary
clock source (defined by FOSC<2:0>)
Secondary – Timer1 oscillator
Postscaled internal clock
Primary clock source (defined by FOSC<2:0>)
Secondary – Timer1 oscillator
Postscaled internal clock
PRI_RUN MODE
SEC_RUN MODE
The Timer1 oscillator should already be
running prior to entering SEC_RUN
mode. If the T1OSCEN bit is not set when
the SCS<1:0> bits are set to ‘01’, entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, device clocks will be delayed until
the oscillator has started. In such situa-
tions, initial oscillator operation is far from
stable and unpredictable operation may
result.
Available Clock and Oscillator Source
Section 27.4 “Two-Speed Start-up”
2011 Microchip Technology Inc.
Section 4.6 “Deep Sleep
Figure
4-1), the primary
Register”).
Related parts for PIC18F25J50
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC18F-LF1XK50](/images/no-image3.png)
Part Number:
Description:
20-Pin USB Flash Microcontrollers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC18F6393T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6493T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8393T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8493T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6585-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 48KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6680-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 64KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F87K90T-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm TRAY
Manufacturer:
Microchip Technology
![PIC18F87K90-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
Manufacturer:
Microchip Technology
![PIC1-100-JT](/images/no-image3.png)
Part Number:
Description:
SURFACE MOUNT POWER INDUCTORS
Manufacturer:
RCD [RCD COMPONENTS INC.]
Datasheet: