PIC18F25J50 MICROCHIP [Microchip Technology], PIC18F25J50 Datasheet - Page 360

• Manufacturer Part Number: PIC18F25J50
• Description: 28/44-Pin, Low-Power, High-Performance USB Microcontrollers with nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

associated internal and/or external hardware must be
PIC18F46J50 FAMILY
The PPBRST bit (UCON<6>) controls the Reset status
when Double-Buffering mode (ping-pong buffering) is
used. When the PPBRST bit is set, all Ping-Pong
Buffer Pointers are set to the Even buffers. PPBRST
has to be cleared by firmware. This bit is ignored in
buffering modes not using ping-pong buffering.
The PKTDIS bit (UCON<4>) is a flag indicating that the
SIE has disabled packet transmission and reception.
This bit is set by the SIE when a SETUP token is
received to allow setup processing. This bit cannot be
set by the microcontroller, only cleared; clearing it
allows the SIE to continue transmission and/or
reception. Any pending events within the Buffer
Descriptor Table will still be available, indicated within
the USTAT register’s FIFO buffer.
The RESUME bit (UCON<2>) allows the peripheral to
perform a remote wake-up by executing resume signal-
ing. To generate a valid remote wake-up, firmware must
set RESUME for 10 ms and then clear the bit. For more
information on resume signaling, see Sections 7.1.7.5,
11.4.4 and 11.9 in the “USB 2.0 Specification”.
The SUSPND bit (UCON<1>) places the module and
supporting circuitry in a low-power mode. The input
clock to the SIE is also disabled. This bit should be set
by the software in response to an IDLEIF interrupt. It
should be reset by the microcontroller firmware after an
ACTVIF interrupt is observed. When this bit is active,
the device remains attached to the bus, but the trans-
ceiver outputs remain Idle. The voltage on the V
may vary depending on the value of this bit. Setting this
bit, before a IDLEIF request, will result in unpredictable
bus behavior.
22.2.2
Prior to communicating over USB, the module’s
configured. Most of the configuration is performed with
the UCFG register
contains most of the bits that control the system level
behavior of the USB module. These include:
• Bus Speed (full speed versus low speed)
• On-Chip Pull-up Resistor Enable
• On-Chip Transceiver Enable
• Ping-Pong Buffer Usage
DS39931D-page 360
Note:
While in Suspend mode, a typical
bus-powered USB device is limited to
2.5 mA of average current. This is the
complete current which may be drawn by
the PIC device and its supporting circuitry.
Care should be taken to assure minimum
current draw when the device enters
Suspend mode.
USB CONFIGURATION REGISTER
(UCFG)
(Register
22-2).The UFCG register
USB
pin
capacitors or magnetic components are required as the
The UCFG register also contains two bits which aid in
module testing, debugging and USB certifications.
These bits control output enable state monitoring and
eye pattern generation.
22.2.2.1
The USB peripheral has a built-in, USB 2.0, full-speed
and low-speed capable transceiver, internally con-
nected to the SIE. This feature is useful for low-cost,
single chip applications. The UTRDIS bit (UCFG<3>)
controls the transceiver; it is enabled by default
(UTRDIS = 0). The FSEN bit (UCFG<2>) controls the
transceiver speed; setting the bit enables full-speed
operation.
The on-chip USB pull-up resistors are controlled by the
UPUEN bit (UCFG<4>). They can only be selected
when the on-chip transceiver is enabled.
The internal USB transceiver obtains power from the
V
cations, V
between 3.0V and 3.6V. The best electrical signal
quality is obtained when a 3.3V supply is used and
locally bypassed with a high-quality ceramic capacitor
(ex: 0.1 F). The capacitor should be placed as close
as possible to the V
V
module is not used, but RC4 or RC5 are used as
general purpose inputs, V
to a power source (such as V
for the RC4 and RC5 pins are dependent upon the
V
The D+ and D- signal lines can be routed directly to their
respective pins on the USB connector or cable (for
hard-wired
D+ and D- drivers have controlled slew rate and output
impedance,
characteristic impedance of the USB cable.
In order to achieve optimum USB signal quality, the D+
and D- traces between the microcontroller and USB
connector (or cable) should be less than 19 cm long.
Both traces should be equal in length and they should
be routed parallel to each other. Ideally, these traces
should be designed to have a characteristic impedance
matching that of the USB cable.
USB
USB
USB
Note:
pin. In order to meet USB signalling level specifi-
supply level.
should always be maintained  V
USB
The USB speed, transceiver and pull-up
should only be configured during the
module setup phase. It is not recom-
mended to switch these settings while the
module is enabled.
applications).
Internal Transceiver
must be supplied with a voltage source
intended
USB
 2011 Microchip Technology Inc.
and V
USB
to
No
DD
should still be connected
SS
). The input thresholds
pins.
additional
match
DD
. If the USB
with
resistors,
the