N25Q064A13EF640F Micron Technology Inc, N25Q064A13EF640F Datasheet - Page 70
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
N25Q064A13EF640F
Manufacturer Part Number
N25Q064A13EF640F
Description
Manufacturer
Micron Technology Inc
Datasheet
1.N25Q064A13EF640F.pdf
(150 pages)
Specifications of N25Q064A13EF640F
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
N25Q064A13EF640F
Manufacturer:
MICRON
Quantity:
1 001
Company:
Part Number:
N25Q064A13EF640F
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
N25Q064A13EF640F
Manufacturer:
MICRON/镁光
Quantity:
20 000
Instructions
9.1.15
70/150
DQ0
DQ1
DQ0
DQ1
*Address bit A23 is “Don’t Care.”
C
S
C
S
Mode 3
Mode 0
18 19 20
Figure 23. Dual Input Extended Fast Program instruction sequence
Quad Input Fast Program
The Quad Input Fast Program (QIFP) instruction is very similar to the Dual Input Fast
Program (DIFP) instruction, except that the data are entered on four pins (pin DQ0, pin
DQ1, pin W/VPP/DQ2 and pin HOLD/ (DQ3) instead of only two. Inputting the data on four
pins instead of two doubles the data transfer bandwidth compared to the Dual Input Fast
Program (DIFP) instruction.
The Quad Input Fast Program (QIFP) instruction is entered by driving Chip Select (S) Low,
followed by the instruction code, three address bytes and at least one data byte on Serial
Data input (DQ0).
If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes
beyond the end of the current page are programmed from the start address of the same
page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip Select (S)
must be driven Low for the entire duration of the sequence.
If more than 256 bytes are sent to the device, previously latched data are discarded and the
last 256 data bytes are guaranteed to be programmed correctly within the same page. If less
than 256 data bytes are sent to device, they are correctly programmed at the requested
addresses without having any effects on the other bytes in the same page.
For optimized timings, it is recommended to use the Quad Input Fast Program (QIFP)
instruction to program all consecutive targeted bytes in a single sequence rather to using
7
6
Data In 1
0
4
5
21
MSB
1
2
3
22 23 24 25 26 27 28 29 30 31 32 33
2
Instruction
0
1
3
7
6
Data In 2
4
5
4
MSB
5
2
3
6
0
1
7
6
7
22 20 18 16
23 21 19 17 15 13 11
8
MSB
Data In 3
5
4
9
3
2
Micron Technology, Inc., reserves the right to change products or specifications without notice.
10 11 12 13 14
0
1
*24-bit Address
7
6
14 12 10
Data In 4
MSB
5
4
3
2
34
1
0
35
8
15 16 17 18 19 20
9
6
7
©2010 Micron Technology, Inc. All rights reserved.
4
6
7
5
Data In 256
2
5
3
4
MSB
0
1
2
3
0
1
N25Q064 - 3 V