N25Q064A13EF640F Micron Technology Inc, N25Q064A13EF640F Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
N25Q064A13EF640F
Manufacturer Part Number
N25Q064A13EF640F
Description
Manufacturer
Micron Technology Inc
Datasheet
1.N25Q064A13EF640F.pdf
(150 pages)
Specifications of N25Q064A13EF640F
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
N25Q064A13EF640F
Manufacturer:
MICRON
Quantity:
1 001
Company:
Part Number:
N25Q064A13EF640F
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
N25Q064A13EF640F
Manufacturer:
MICRON/镁光
Quantity:
20 000
N25Q064 - 3 V
2
2.1
2.2
2.3
2.4
Signal descriptions
Serial data output (DQ1)
This output signal is used to transfer data serially out of the device. Data are shifted out on
the falling edge of Serial Clock (C). When used as an Input, It is latched on the rising edge
of the Serial Clock (C).
In the Extended SPI protocol, during the Quad and Dual Input Fast Program (QIFP, DIFP)
instructions and during the Quad and Dual Input Extended Fast Program (QIEFP, DIEFP)
instructions, pin DQ1 is used also as an input.
In the Dual I/O SPI protocol (DIO-SPI) the DQ1 pin always acts as an input/output.
In the Quad I/O SPI protocol (QIO-SPI) the DQ1 pin always acts as an input/output, with the
exception of the Program or Erase cycle performed with the Enhanced Program Supply
Voltage (VPP). In this case the device temporarily goes in Extended SPI protocol. The
protocol then becomes QIO-SPI as soon as the VPP pin voltage goes low.
Serial data input (DQ0)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be programmed. Values are latched on the rising edge of Serial
Clock (C). Data are shifted out on the falling edge of the Serial Clock (C).
In the Extended SPI protocol, during the Quad and Dual Output Fast Read (QOFR, DOFR)
and the Quad and Dual Input/Output Fast Read (QIOFR, DIOFR) instructions, pin DQ0 is
also used as an input/output.
In the DIO-SPI protocol the DQ0 pin always acts as an input/output.
In the QIO-SPI protocol, the DQ0 pin always acts as an input/output, with the exception of
the Program or Erase cycle performed with the VPP. In this case the device temporarily
goes in Extended SPI protocol. Then, the protocol returns to QIO-SPI as soon as the VPP
pin voltage goes low.
Serial Clock (C)
This input signal provides the timing for the serial interface. Instructions, addresses, or data
present at serial data input (DQ0) are latched on the rising edge of Serial Clock (C). Data
are shifted out on the falling edge of the Serial Clock (C).
Chip Select (S)
When this input signal is high, the device is deselected and serial data output (DQ1) is at
high impedance. Unless an internal program, erase or write status register cycle is in
progress, the device will be in the standby power mode. Driving Chip Select (S) low enables
the device, placing it in the active power mode.
After power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2010 Micron Technology, Inc. All rights reserved.
Signal descriptions
15/150