PIC16F767-E/ML Microchip Technology, PIC16F767-E/ML Datasheet - Page 92

• Manufacturer Part Number: PIC16F767-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F767-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F7X7
9.5.1
The user must configure the RC2/CCP1 pin as an
output by clearing the TRISC<2> bit.
9.5.2
Timer1 must be running in Timer mode or Synchro-
nized Counter mode if the CCP module is using the
compare feature. In Asynchronous Counter mode, the
compare operation may not work.
9.5.3
When Generate Software Interrupt mode is chosen, the
CCP1 pin is not affected. The CCP1IF or CCP2IF bit is
set, causing a CCP interrupt (if enabled).
TABLE 9-3:
DS30498C-page 90
0Bh,8Bh,
10Bh,18Bh
0Ch
0Dh
8Ch
8Dh
87h
0Eh
0Fh
10h
15h
16h
17h
1Bh
1Ch
1Dh
95h
96h
97h
Legend:
Note 1:
Address
Note:
INTCON
PIR1
PIR2
PIE1
PIE2
TRISC
TMR1L
TMR1H
T1CON
CCPR1L
CCPR1H
CCP1CON
CCPR2L
CCPR2H
CCP2CON
CCPR3L
CCPR3H
CCP3CON
x = unknown, u = unchanged, — = unimplemented, read as ‘0’. Shaded cells are not used by Capture and Timer1.
The PSP is not implemented on the PIC16F737/767 devices; always maintain these bits clear.
CCP PIN CONFIGURATION
Clearing the CCP1CON register will force
the RC2/CCP1 compare output latch to
the default low level. This is not the
PORTC I/O data latch.
TIMER1 MODE SELECTION
SOFTWARE INTERRUPT MODE
Name
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE AND TIMER1
PSPIE
PORTC Data Direction Register
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
Capture/Compare/PWM Register 1 (LSB)
Capture/Compare/PWM Register 1 (MSB)
Capture/Compare/PWM Register 2 (LSB)
Capture/Compare/PWM Register 2 (MSB)
Capture/Compare/PWM Register 3 (LSB)
Capture/Compare/PWM Register 3 (MSB)
PSPIF
OSFIF
OSFIE
Bit 7
GIE
—
—
—
—
(1)
(1)
T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON -000 0000 -uuu uuuu
CMIE
CMIF
Bit 6
PEIE
ADIF
ADIE
—
—
—
TMR0IE
CCP1X
CCP2X
CCP3X
LVDIE
LVDIF
RCIE
Bit 5
RCIF
CCP1Y
CCP2Y
CCP3Y
INT0IE
Bit 4
TXIF
TXIE
—
—
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
CCP3M3 CCP3M2 CCP3M1 CCP3M0 --00 0000 --00 0000
SSPIF
SSPIE
BCLIE
BCLIF
Bit 3
RBIE
9.5.4
In this mode, an internal hardware trigger is generated
which may be used to initiate an action.
The special event trigger output of CCP1 resets the
TMR1 register pair. This allows the CCPR1 register to
effectively be a 16-bit programmable period register for
Timer1.
The special event trigger output of CCP2 resets the
TMR1 register pair and starts an A/D conversion (if the
A/D module is enabled).
Note:
TMR0IF
CCP1IF
CCP1IE TMR2IE
Bit 2
—
—
SPECIAL EVENT TRIGGER
The special event trigger from the CCP1
and CCP2 modules will not set interrupt
flag bit, TMR1IF (PIR1<0>).
TMR2IF
CCP3IF
CCP3IE
INT0IF
Bit 1
TMR1IE 0000 0000 0000 0000
 2004 Microchip Technology Inc.
TMR1IF 0000 0000 0000 0000
CCP2IF 000- 0-00 000- 0-00
CCP2IE 000- 0-00 000- 0-00
Bit 0
RBIF
0000 000x 0000 000u
1111 1111 1111 1111
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
POR, BOR
Value on:
Value on
all other
Resets