ATMEGA168PA-PU Atmel, ATMEGA168PA-PU Datasheet - Page 45

• Manufacturer Part Number: ATMEGA168PA-PU
• Description: MCU, 8BIT, AVR, 16K FLASH, 28PDIP
• Manufacturer: Atmel

Specifications of ATMEGA168PA-PU

• Controller Family/series: Atmega
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 20MHz
• No.: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 16KB
• Oscillator Type: External, Internal
• Rohs Compliant: Yes

9.11.2
9.11.3
8271C–AVR–08/10
MCUCR – MCU Control Register
PRR – Power Reduction Register
• Bit 6 – BODS: BOD Sleep
The BODS bit must be written to logic one in order to turn off BOD during sleep, see
on page
BODSE in MCUCR. To disable BOD in relevant sleep modes, both BODS and BODSE must first
be set to one. Then, to set the BODS bit, BODS must be set to one and BODSE must be set to
zero within four clock cycles.
The BODS bit is active three clock cycles after it is set. A sleep instruction must be executed
while BODS is active in order to turn off the BOD for the actual sleep mode. The BODS bit is
automatically cleared after three clock cycles.
• Bit 5 – BODSE: BOD Sleep Enable
BODSE enables setting of BODS control bit, as explained in BODS bit description. BOD disable
is controlled by a timed sequence.
Note:
• Bit 7 – PRTWI: Power Reduction TWI
Writing a logic one to this bit shuts down the TWI by stopping the clock to the module. When
waking up the TWI again, the TWI should be re initialized to ensure proper operation.
• Bit 6 – PRTIM2: Power Reduction Timer/Counter2
Writing a logic one to this bit shuts down the Timer/Counter2 module in synchronous mode (AS2
is 0). When the Timer/Counter2 is enabled, operation will continue like before the shutdown.
• Bit 5 – PRTIM0: Power Reduction Timer/Counter0
Writing a logic one to this bit shuts down the Timer/Counter0 module. When the Timer/Counter0
is enabled, operation will continue like before the shutdown.
• Bit 4 – RReserved
This bit is reserved in ATmega48A/48PA/88A/88PA/168A/168PA/328/328P and will always read
as zero.
• Bit 3 – PRTIM1: Power Reduction Timer/Counter1
Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1
is enabled, operation will continue like before the shutdown.
• Bit 2 – PRSPI: Power Reduction Serial Peripheral Interface
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
Bit
0x35 (0x55)
Read/Write
Initial Value
Bit
(0x64)
Read/Write
Initial Value
1. BODS and BODSE only available for picoPower devices ATmega48PA/88PA/168PA/328P
39. Writing to the BODS bit is controlled by a timed sequence and an enable bit,
PRTWI
R/W
7
0
R
7
–
0
PRTIM2
BODS
R/W
R/W
6
0
6
0
(1)
(1)
PRTIM0
BODSE
R/W
5
0
R/W
5
0
(1)
(1)
R
4
–
0
PUD
R/W
0
4
PRTIM1
R/W
3
0
R
3
–
0
PRSPI
R/W
2
0
R
2
–
0
PRUSART0
IVSEL
R/W
R/W
1
0
1
0
IVCE
R/W
PRADC
0
0
R/W
0
0
Table 9-1
MCUCR
PRR
45