TMOV25SP385M Littelfuse Inc, TMOV25SP385M Datasheet - Page 55

TMOV VARISTOR PB FREE 25S

TMOV25SP385M

Manufacturer Part Number
TMOV25SP385M
Description
TMOV VARISTOR PB FREE 25S
Manufacturer
Littelfuse Inc
Series
iTMOV®r
Datasheets

Specifications of TMOV25SP385M

Varistor Voltage
682V
Current-surge
20kA
Number Of Circuits
1
Maximum Ac Volts
385VAC
Energy
430J
Package / Case
Disc 25mm 3-Lead
Suppressor Type
Varistor
Peak Surge Current @ 8/20µs
20000A
Varistor Case
25mm DISC
Clamping Voltage Vc Max
1010V
Peak Energy (10/1000us)
430J
Voltage Rating Vdc
682V
Voltage Rating Vac
385V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Maximum Dc Volts
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
• For ratings of individual members of a series, see Device Ratings and Specifications chart.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any
other conditions above those indicated in the operational sections of this specification is not implied.
©2009 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com/series/AUML.html for current information.
RoHS
Size Table
Applications
Absolute Maximum Ratings
Continuous
Steady State Applied Voltage:
Transient:
Operating Ambient Temperature Range (T
Storage Temperature Range (T
Temperature Coefficient (DV) of Clamping Voltage (V
Metric
3225
4532
5650
3216
Suppression of
inductive switching
or other transient
events such as EFT
and surge voltage at
the circuit board level
ESD protection for
components sensitive
to IEC 61000-4-2, MIL -
STD-883C, Method
3015.7 , and other
industry specifications
(See Also the MLE
or MLN Series)
AUML Varistor Series
1206
1812
2220
1210
EIA
DC Voltage Range (V
Load Dump Energy, (W
Jump Start Capability (5 minutes), (V
STG
)
Provides on-board
transient voltage
protection for ICs
and transistors
Used to help achieve
electromagnetic
compliance of
end products
Replace larger surface
mount TVS Zeners in
many applications
M(DC)
A
)
LD
)
)
Varistor Products
Surface Mount Multilayer Varistors (MLVs) > AUML Series
C
) at Specified Test Current
JUMP
Revision: November 5, 2009
)
51
The AUML Series of Multilayer Transient Surge Suppressors
was specifically designed to suppress the destructive
transient voltages found in an automobile. The most common
transient condition results from large inductive energy
discharges. The electronic systems in the automobile, e.g.
antilock brake systems, direct ignition systems, engine
control, airbag control systems, wiper motor controls, etc.,
are susceptible to damage from these voltage transients and
thus require protection. The AUML transient suppressors
have temperature independent suppression characteristics
affording protection from -55ºC to 125ºC.
The AUML suppressor is manufactured from semiconducting
ceramics which offer rugged protection and excellent
transient energy absorption in a small package. The devices
are available in ceramic leadless chip form, eliminating lead
inductance and assuring fast speed of response to transient
surges. These Suppressors require significantly smaller
space and land pads than Silicon TVS diodes, offering greater
circuit board layout flexibility for the designer.
Also see the Littelfuse ML, MLN and MLE Series of
Multilayer Suppressors.
Description
Features
AEC - Q200 compliant
RoHS Compliant
Load Dump energy
rated per SAE
Specification J1113
Leadless, surface
mount chip form
“Zero” Lead
Inductance
Variety of energy
ratings available
No temperature
derating up to
125ºC ambient
AUML Series
-55 to +125
-55 to +150
1.5 to 25
<0.01
24.5
18
Units
%/
O
O
V
V
J
C
C
O
C
High peak surge
current capability
Low Profile, compact
industry standard
chip size; (1206, 1210,
1812 and 2220 Sizes)
Inherent bidirectional
clamping
No Plastic or epoxy
packaging assures
better than 94V-0
flammability rating
AUML Varistor Series

Related parts for TMOV25SP385M