101-1279 Rabbit Semiconductor, 101-1279 Datasheet - Page 57
101-1279
Manufacturer Part Number
101-1279
Description
PLASTIC ENCLOSURE FOR BL4S100
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1258.pdf
(144 pages)
Specifications of 101-1279
Accessory Type
Enclosure
Product
Prototyping Accessories
Processor Type
BL4S100
Board Size
146 mm x 96 mm x 16 mm
Interface Type
Ethernet
For Use With/related Products
BL4S100
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
316-1159
- Current page: 57 of 144
- Download datasheet (3Mb)
FUNCTION DESCRIPTION
PARAMETERS
BL4S100 User’s Manual
int setCapture(int channel, int mode, int edge, word options);
Sets up the channel as an event capture input, with selectable modes and edge settings.
The counter will run from a gated main or prescaled clock signal based on the run cri-
teria of the selected mode, and begin/end events can be set to capture the count at the
time of these events. Optionally, a second channel can be set (which shares the same
RIO channel input block as
getBegin()
Counter()
channel
mode
NOTE: If an end event occurs before the begin event, the count will begin then end
edge
immediately on the begin event, and the end count will be 1. The begin count will be 0
or 1 based on the edge that triggered the event (0 = rising, 1 = falling).
to force a reset of the counter.
and
getEnd()
channel to use for the begin event input for all modes except
CNT_TIL_END
0–11 (pins IN0–IN11)
mode macro for the counter/timer:
BL_CNT_RUN
BL_CNT_BEGIN_END
count until end event detected
BL_CNT_TIL_END
BL_CNT_ON_BEGIN
edge/state macro setting for the begin event for all modes except
BL_CNT_TIL_END
The following two settings are only for the
mode:
BL_EVENT_RISE
BL_EVENT_FALL
BL_EVENT_BOTH
BL_BEGIN_HIGH
BL_BEGIN_LOW
channel
to read the captured count values and use
setCapture
— continuous count mode
, then it specifies the end event input.,
) for two-signal begin/end event detection. Use
, then it specifies the end event:
— count until end event detected
— count while begin signal is active
— begin active while signal is low
— start count on begin event, continue to
— begin event on rising edge
— begin event on falling edge
— begin event on any edge
— begin active while signal is high
BL_CNT_ON_BEGIN
reset-
BL_
55
Related parts for 101-1279
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2120 FRCTNLOCK
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT APPLCTN RABBITCORE RCM4010
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT MESH NETWORK ADD-ON RCM4510W
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT APPLICATION SIMPLE SENSOR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
PWR SUPPLY UNIV 110/240VAC-12VDC
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
IC CPU RABBIT2000 30MHZ 100PQFP
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
IC CPU RABBIT4000 128-LQFP
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
IC MPU RABIT3000A 55.5MHZ128LQFP
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM4010
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
RCM4110 RABBITCORE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM2000
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3000
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MCU RCM4000 RABBITCORE
Manufacturer:
Rabbit Semiconductor
Datasheet: