XC56309VL100A Freescale Semiconductor, XC56309VL100A Datasheet - Page 225

• Manufacturer Part Number: XC56309VL100A
• Description: IC DSP 24BIT 100MHZ 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of XC56309VL100A

• Interface: Host Interface, SSI, SCI
• Clock Rate: 100MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 24kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 196-MAPBGA
• Device Core Size: 24b
• Format: Fixed Point
• Clock Freq (max): 100MHz
• Mips: 100
• Device Input Clock Speed: 100MHz
• Ram Size: 102KB
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

; specifying the address to start loading the program words and then 3 bytes
; forming 24-bit words for each program word to be loaded.
; The program words will be stored in contiguous PRAM memory locations
; starting at the specified starting address.
; After reading the program words, program execution starts from the same
; address where loading started.
; The Host Interface bootstrap load program may be stopped by setting the
; Host Flag 0 (HF0). This will start execution of the loaded program from
; the specified starting address.
;
; The base address of the HI08 in multiplexed mode is 0x80 and is not
; modified by the bootstrap code. All the address lines are enabled
; and should be connected accordingly.
;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; If MD:MC:MB:MA=1111, then it loads the program RAM from the Host
; Interface programmed to operate in the MC68302 (IMP) bus mode,
; in single-strob pin configuration.
; The HOST MC68302 bootstrap code expects accesses that are byte wide.
; The HOST MC68302 bootstrap code expects to read 3 bytes forming a 24-bit word
; specifying the number of program words, 3 bytes forming a 24-bit word
; specifying the address to start loading the program words and then 3 bytes
; forming 24-bit words for each program word to be loaded.
; The program words will be stored in contiguous PRAM memory locations
; starting at the specified starting address.
; After reading the program words, program execution starts from the same
; address where loading started.
; The Host Interface bootstrap load program may be stopped by setting the
; Host Flag 0 (HF0). This will start execution of the loaded program from
; the specified starting address.
;
;;;;;;;;;;;;;;;;;;;; MEMORY EQUATES ;;;;;;;;;;;;;;;;;;;;;;;;
EQUALDATA
start_dram
length_dram
start_xram
length_xram
start_yram
length_yram
start_pram
length_pram
;;
;;;;;;;;;;;;;;;;;;;; GENERAL EQUATES ;;;;;;;;;;;;;;;;;;;;;;;;
;;
BOOT
Freescale Semiconductor
page
if
else
endif
equ
132,55,0,0,0
opt
equ
(EQUALDATA)
equ
equ
equ
equ
equ
equ
equ
equ
$D00000
mex
1
0
$1c00
0
$1c00
0
$1c00
0
$5000
;; 1 if xram and yram are of equal
;; size and addresses, 0 otherwise.
;; 24k X and Y RAM
;; same addresses
;; 7k XRAM
;; 7k YRAM
;; 20k PRAM
; this is the location in P memory
DSP56309 User’s Manual, Rev. 1
Bootstrap Code
A-3