MC9S08EL16CTJ Freescale Semiconductor, MC9S08EL16CTJ Datasheet - Page 345

• Manufacturer Part Number: MC9S08EL16CTJ
• Description: MCU 16KB FLASH SLIC 20TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08EL16CTJ

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP
• Processor Series: S08EL
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI, I2C, SLIC
• Maximum Clock Frequency: 200 KHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08EL32AUTO, DEMO9S08EL32
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: DEMO9S08EL32 - BOARD DEMO FOR 9S08 EL MCUDEMO9S08EL32AUTO - DEMO BOARD EL32 AUTO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
2
3
A.12 AC Characteristics
This section describes ac timing characteristics for each peripheral system.
A.12.1
Freescale Semiconductor
1
2
3
4
5
Typical values assume V
and are not tested in production.
1 LSB = (V
Based on input pad leakage current. Refer to pad electricals.
Num
Characteristic
Typical values are based on characterization data at V
This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to
override reset requests from internal sources.
When any reset is initiated, internal circuitry drives the reset pin low for about 66 cycles of t
frequency changes to the untrimmed DCO frequency (f
to 0, and there is an extra divide-by-two because BDIV is reset to 0:1. After other resets trim stays at the pre-reset value.
This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or
may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case.
Timing is shown with respect to 20% V
Temp sensor
Temp sensor
1
2
3
4
5
6
voltage
slope
C
D
D
D
D
D
C
REFH
Control Timing
Bus frequency (t
Internal low power oscillator period
External reset pulse width
Reset low drive
Pin interrupt pulse width
Port rise and fall time —
Low output drive (PTxDS = 0) (load = 50 pF)
Port rise and fall time —
High output drive (PTxDS = 1) (load = 50 pF)
Asynchronous path
Synchronous path
- V
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
Slew rate control enabled (PTxSE = 1)
Slew rate control disabled (PTxSE = 0)
REFL
-40°C to 25°C
25°C to 125°C
25°C
)/2
DD
N
= 5.0 V, Temp = 25°C, f
MC9S08EL32 Series and MC9S08SL16 Series Data Sheet, Rev. 3
Conditions
3
cyc
= 1/f
4
2
Table A-12. ADC Characteristics (continued)
Rating
Bus
2
DD
)
and 80% V
Table A-13. Control Timing
ADCK
C
D
D
DD
= 1.0 MHz unless otherwise stated. Typical values are for reference only
DD
reset
V
levels. Temperature range –40°C to 125°C.
Symb
TEMP25
5
= 5.0V, 25°C unless otherwise stated.
5
m
= (f
dco_ut
)/4) because TRIM is reset to 0x80 and FTRIM is reset
Min
t
t
t
Symbol
—
—
—
ILIH,
Rise
Rise
t
t
t
rstdrv
f
extrst
LPO
Bus
, t
, t
t
IHIL
Fall
Fall
3.266
3.638
1.396
Typ
1.5 x t
66 x t
1
Min
800
100
100
dc
—
—
—
—
cyc
Appendix A Electrical Characteristics
cyc
cyc
Max
—
—
—
. After POR reset, the bus clock
Typ
40
75
11
35
—
—
mV/°C
Unit
1
V
1500
Max
20
—
—
—
—
—
—
—
Comment
MHz
Unit
μs
ns
ns
ns
ns
ns
347