PIC18F66J15-I/PT Microchip Technology, PIC18F66J15-I/PT Datasheet - Page 51

• Manufacturer Part Number: PIC18F66J15-I/PT
• Description: IC PIC MCU FLASH 48KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J15-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 96KB (48K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.2
The MCLR pin provides a method for triggering a hard
external Reset of the device. A Reset is generated by
holding the pin low. PIC18 extended microcontroller
devices have a noise filter in the MCLR Reset path
which detects and ignores small pulses.
The MCLR pin is not driven low by any internal Resets,
including the WDT.
5.3
A Power-on Reset condition is generated on-chip
whenever V
allows the device to start in the initialized state when
V
To take advantage of the POR circuitry, tie the MCLR
pin through a resistor (1 kΩ to 10 kΩ) to V
eliminate external RC components usually needed to
create a Power-on Reset delay. A minimum rise rate for
V
time, see Figure 5-2.
When the device starts normal operation (i.e., exits the
Reset
(voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
POR events are captured by the POR bit (RCON<1>).
The state of the bit is set to ‘0’ whenever a POR occurs;
it does not change for any other Reset event. POR is
not reset to ‘1’ by any hardware event. To capture
multiple events, the user manually resets the bit to ‘1’
in software following any POR.
5.4
The PIC18F87J10 family of devices incorporate a
simple BOR function when the internal regulator is
enabled (ENVREG pin is tied to V
below V
T
or may not occur if V
T
V
Once a BOR has occurred, the Power-up Timer will
keep the chip in Reset for T
V
running, the chip will go back into a Brown-out Reset
and the Power-up Timer will be initialized. Once V
rises above V
additional time delay.
© 2009 Microchip Technology Inc.
BOR
BOR
DD
DD
DD
DD
is adequate for operation.
rises above V
. The chip will remain in Brown-out Reset until
drops below V
is specified (parameter D004). For a slow rise
(parameter 35) will reset the device. A Reset may
BOR
condition),
Master Clear (MCLR)
Power-on Reset (POR)
Brown-out Reset (BOR)
DD
(parameter D005) for greater than time
BOR
rises above a certain threshold. This
, the Power-up Timer will execute the
BOR
BOR
DD
device
.
falls below V
while the Power-up Timer is
PWRT
operating
DD
). Any drop of V
(parameter 33). If
BOR
for less than
DD
parameters
. This will
DD
DD
PIC18F87J10 FAMILY
FIGURE 5-2:
5.4.1
The BOR bit always resets to ‘0’ on any BOR or POR
event. This makes it difficult to determine if a BOR
event has occurred just by reading the state of BOR
alone. A more reliable method is to simultaneously
check the state of both POR and BOR. This assumes
that the POR bit is reset to ‘1’ in software immediately
after any POR event. If BOR is ‘0’ while POR is ‘1’, it
can be reliably assumed that a BOR event has
occurred.
If the voltage regulator is disabled, Brown-out Reset
functionality is disabled. In this case, the BOR bit
cannot be used to determine a BOR event. The BOR
bit is still cleared by a POR event.
Note 1: External Power-on Reset circuit is required
V
2: R < 40 kΩ is recommended to make sure that
3: R1 ≥ 1 kΩ will limit any current flowing into
DD
DETECTING BOR
D
only if the V
The diode D helps discharge the capacitor
quickly when V
the voltage drop across R does not violate
the device’s electrical specification.
MCLR from external capacitor C, in the event
of MCLR/V
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
V
DD
R
C
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW V
DD
PP
DD
R1
power-up slope is too slow.
pin breakdown, due to
powers down.
DD
PIC18F87J10
MCLR
POWER-UP)
DS39663F-page 49