PIC18F66J15-I/PT Microchip Technology, PIC18F66J15-I/PT Datasheet - Page 270

• Manufacturer Part Number: PIC18F66J15-I/PT
• Description: IC PIC MCU FLASH 48KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J15-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 96KB (48K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87J10 FAMILY
21.5
Figure 21-3 shows the operation of the A/D Converter
after the GO/DONE bit has been set and the
ACQT<2:0> bits are cleared. A conversion is started
after the following instruction to allow entry into Sleep
mode before the conversion begins.
Figure 21-4 shows the operation of the A/D Converter
after the GO/DONE bit has been set, the ACQT<2:0>
bits are set to ‘010’ and a 4 T
been selected before the conversion starts.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The A/D Result register
pair will NOT be updated with the partially completed
A/D
ADRESH:ADRESL registers will continue to contain
the value of the last completed conversion (or the last
value written to the ADRESH:ADRESL registers).
After the A/D conversion is completed or aborted, a
2 T
started. After this wait, acquisition on the selected
channel is automatically started.
FIGURE 21-3:
FIGURE 21-4:
DS39663F-page 268
Note:
(Holding capacitor continues
acquiring input)
AD
Set GO/DONE bit
wait is required before the next acquisition can be
1
conversion
A/D Conversions
T
T
Set GO/DONE bit
CY
Automatic
Acquisition
Time
ACQT
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
Holding capacitor is disconnected from analog input (typically 100 ns)
2
- T
AD
Cycles
Conversion starts
T
3
AD
sample.
A/D CONVERSION T
A/D CONVERSION T
1 T
4
AD
b9
2 T
Conversion starts
(Holding capacitor is disconnected)
AD
1
This
AD
acquisition time has
b8
3 T
b9
2
AD
means
Next Q4: ADRESH:ADRESL is loaded, GO/DONE bit is cleared,
b7
Next Q4: ADRESH/ADRESL is loaded, GO/DONE bit is cleared,
4 T
b8
3
AD
AD
AD
b6
5 T
CYCLES (ACQT<2:0> = 000, T
CYCLES (ACQT<2:0> = 010, T
ADIF bit is set, holding capacitor is reconnected to analog input.
the
ADIF bit is set, holding capacitor is connected to analog input.
b7
4
AD
b5
6 T
T
5
b6
AD
AD
b4
7 T
Cycles
21.6
An A/D conversion can be started by the “Special Event
Trigger” of the ECCP2 module. This requires that the
CCP2M<3:0> bits (CCP2CON<3:0>) be programmed
as ‘1011’ and that the A/D module is enabled (ADON
bit is set). When the trigger occurs, the GO/DONE bit
will be set, starting the A/D acquisition and conversion
and the Timer1 (or Timer3) counter will be reset to zero.
Timer1 (or Timer3) is reset to automatically repeat the
A/D acquisition period with minimal software overhead
(moving ADRESH/ADRESL to the desired location).
The appropriate analog input channel must be selected
and the minimum acquisition period is either timed by
the user, or an appropriate T
the Special Event Trigger sets the GO/DONE bit (starts
a conversion).
If the A/D module is not enabled (ADON is cleared), the
Special Event Trigger will be ignored by the A/D module
but will still reset the Timer1 (or Timer3) counter.
b5
6
AD
b3
8
Use of the ECCP2 Trigger
b4
T
7
AD
b2
9 T
b3
8
AD
b1
10
ACQ
ACQ
T
b2
9
AD
© 2009 Microchip Technology Inc.
b0
11
= 0)
= 4 T
ACQ
10
b1
time is selected before
AD
b0
)
11